Freewing Mirage 2000C V2 “Tiger Meet” 80mm EDF - Official Thread

[Tipstalled10]

Try it and tell us. The rotor is like $12. Note it's not just the number of blades but the blade has a different design and pitch too.

I definitely will. I’ll also put a power meter on the setup to see what kind of amp draw it has. Was hoping someone else had tried this. This is part of the fun of this hobby!!😇

[Evan D]

Try it and tell us. The rotor is like $12. Note it's not just the number of blades but the blade has a different design and pitch too.

[Tipstalled10]

I have the 3658-2150Kv motor with 12 blades. Would changing out to the 9 blade give more top end? I would likely give up some thrust. What say ye!!😃

[StratoJoe]

I start in the middle of the recommend range and move back. If it starts getting too scary to fly I move up a little.

[kallend]

Hello, Is there anyone who knows what the Best CG on this jet Gen 2 4000 mah 6s?? always wanted one

"Best" in what context?

[ken Luper]

Hello, Is there anyone who knows what the Best CG on this jet Gen 2 4000 mah 6s?? always wanted one

[Fredardi]

I don't think anything will help. It sounds like play in the servos and linkage where if you give it some right it stays a little right when you go back to center and then you give it left and it stays a little left when you go back to center again.

ok I'll check ...thanks

[Evan D]

I don't think anything will help. It sounds like play in the servos and linkage where if you give it some right it stays a little right when you go back to center and then you give it left and it stays a little left when you go back to center again.

[Fredardi]

Maybe add one! Expo only helps if it's you that is moving the stick.

I will try to go to 40% expo and see if it helps... thanks

[SanExup]

Maybe add one! Expo only helps if it's you that is moving the stick.

[Fredardi]

Fredardi Are you using a gyro? If so turn the gain down.

No no gyro installed

[SanExup]

Fredardi Are you using a gyro? If so turn the gain down.

[Fredardi]

Instead of changing it with servo travel do it in the D/R menu.

Yes as you said I have solved thanks .Done my maiden plus other 6 flights and is absolutely a blast to fly ! Only one thing I have to set better its when I pass at full speed it's like it behave with the ailerons and does not go straight but the wing do small mouvements on straight like going from left to right and from right to left it does not make my wings go level.I check the ailerons and they are trimmed perfectly as also the rudder.I set the ailerons at 35% rate with 35 % expo...Maybe I have to add more expo ?

[kallend]

Just thought I'd repost links to the 3DP nozzle and cockpit parts for the Mirage:

https://www.thingiverse.com/thing:6165664

[Fredardi]

Instead of changing it with servo travel do it in the D/R menu.

Thank's I'll try this way.

[Evan D]

Instead of changing it with servo travel do it in the D/R menu.

[Fredardi]

Hello , I can complete my radio settings on my Dx9 Black. I set to elevons and everything work fine but if I want to modify the elevator throw differently than my aileron throws it will modify also my aileron throws .I can't modify both differently .I also try on Elevon B but still the problem .I use a AR 620 Spectrum receiver.Any suggestions ? Thanks

[Evan D]

I have a like new Mirage kit+ for sale on RCG, two flights on it, no damage at all, no hanger rash. Selling without the 2150 EDF or ESC but I could add a 9b 1920 EDF and non reversing ESC cheap if someone is interested.

[Olivier_]

Where are these parts attached?
I don't see anything on the instructions.

I finally found it by looking at the photos on the website.

[Evan D]

Vertical stab towards the top.