If you did this how does your radio, telemetry and esc LVC appear and is it smart telemetry so that it gives you individual cell readings/warnings to ensure you know the 6s pack is running out or is it based on total voltage of both packs together and will you get LVC warning at the right time ? I would have thought same mah for both lipos takes out the risk of a false reading but I guess it is down to what you are comfortable with. Maybe run em down to lvc on the ground first ?
Official 90mm Avanti S EDF Sport Jet Thread
Collapse
X
-
-
Can anyone tell me what is the maximum usable width of the battery compartment in the 90mm Avanti-S?Comment
-
Comment
-
Today we had a very nice and pretty warm weather (as for this season): 9 degrees C with lots of Sun and no wind.
Perfect weather for the maiden.
I've also the 80mm version so I'll be comparing those 2.
All settings as per manual. Battery 6s 5500mAh. Take off weight 3.9kg
First positive surprise: Plane takes off by itself without the need to pull the elevator (diving nose wheel of 80mm version was a nightmare to take off on grass compared to this).
CG seem to be pretty good (way better than original one of 80mm version)
Throws - as suspected - too much ailerons and elevator on low rate for me. Reduced by around 20% each. Now, the roll rate is ab. 0.8-1 rotation per second. Haven't tried high rates (most likely I'll program the original low rates as high rates).
After landing, I've noticed that the elevators are visibly down (from the zero point). I'm wondering if it's CG or something else.
I've also had to trim the ailerons to the right. Could be either the EDF torque or the flaps aren't 100% level (to be checked).
Landing was another surprise compared to 80mm version. First, I tried to land with a bit of throttle and full flaps. Plane just went through the whole runway and I had to go around. Second try was on zero throttle and only then it landed nicely (but still gliding pretty well).
Perhaps adding flaps would help to slow it down?
Second flight was to check gyro. Model was even more rock solid (this plane doesn't seem to need gyro at all).
Regarding the power system - 6s is definitely not overpowered
It has nice vertical but pretty limited.
I'm going to swap the fans and use the 4068-1750kV version on 6s to see what changes.Cheers!
MarekComment
-
Folks, if you're looking for a wing protection bags.
Here's what I got. They seem to fit perfectly (the "30E and smaller" size").
It does fit both wings and the wing tube (separate pockets)
Cheers!
MarekComment
-
Looks like someone else experienced similar issues on maidenToday we had a very nice and pretty warm weather (as for this season): 9 degrees C with lots of Sun and no wind.
Perfect weather for the maiden.
I've also the 80mm version so I'll be comparing those 2.
All settings as per manual. Battery 6s 5500mAh. Take off weight 3.9kg
First positive surprise: Plane takes off by itself without the need to pull the elevator (diving nose wheel of 80mm version was a nightmare to take off on grass compared to this).
CG seem to be pretty good (way better than original one of 80mm version)
Throws - as suspected - too much ailerons and elevator on low rate for me. Reduced by around 20% each. Now, the roll rate is ab. 0.8-1 rotation per second. Haven't tried high rates (most likely I'll program the original low rates as high rates).
After landing, I've noticed that the elevators are visibly down (from the zero point). I'm wondering if it's CG or something else.
I've also had to trim the ailerons to the right. Could be either the EDF torque or the flaps aren't 100% level (to be checked).
Landing was another surprise compared to 80mm version. First, I tried to land with a bit of throttle and full flaps. Plane just went through the whole runway and I had to go around. Second try was on zero throttle and only then it landed nicely (but still gliding pretty well).
Perhaps adding flaps would help to slow it down?
Second flight was to check gyro. Model was even more rock solid (this plane doesn't seem to need gyro at all).
Regarding the power system - 6s is definitely not overpowered
It has nice vertical but pretty limited.
I'm going to swap the fans and use the 4068-1750kV version on 6s to see what changes.Comment
-
Comment
-
When will the TV systems be available for preorders? When will we see a comparison between the 6s and 8s versions? Is there going to be any mods needed for the 8s version to get the Cg correct for the best flying setup? I have the green 8s version in the box awaiting release of the TV module and info on the above questions. Also wondering what you guys think about the new gyro? Will we need a second gyro for the TV? TIA!!!!Comment
-
Motion doesn't do preorders on parts like they sometime do on planes. The TV unit is available from Hong Kong now. Mods needed for the 8S version? Mine is balanced great and flying great on 8S.What issue do you think there is? I am using the stock gyro and am fine with it. I would think if you are planning on hovering a separate gyro for that would help, like the Ares with two gyros. I am not planning on adding the TV unit. I've got a lot of flights on my green 8S now, flew it again today. Flies really nice.
When will the TV systems be available for preorders? When will we see a comparison between the 6s and 8s versions? Is there going to be any mods needed for the 8s version to get the Cg correct for the best flying setup? I have the green 8s version in the box awaiting release of the TV module and info on the above questions. Also wondering what you guys think about the new gyro? Will we need a second gyro for the TV? TIA!!!!Comment
-
-
Using 8S packs it was impossible to balance the model with anything bigger than a 4400. Using the balance jig a nice added feature I was able to achieve perfect balance, and the pack was a good inch plus in front of the blue box. My main batteries are 5900 & 6400 8SHV packs. With as big as the battery area is, it occurred to me that unless one was to use the VT section cg would not be easily achievable.
3-D printing to the rescue. Thanks to a post by my friend Ron. I downloaded a print file, The printed part weighs 2 ounces And gives the jet a really nice finished look.
Now my 6400 HV pack fits without being jammed against the blue box.
By the way, the maiden flight on the 4400s was fabulous! Without a doubt, the best first flight I’ve had on recent models!Comment
-
Yes, unless you have a wider selection of battery weights it may need creativity to get the balance where you want it. It’s not the mAh that matters, it’s the weight. My 800g of 5300 6+2 balances to the point I drag my tail and is how I like mine balanced.Comment
-






Comment