Hey Jet
no worries I know your not knocking MRC at all , I was just saying I think they are a good company.
I am involved with imports that far exceed the hobby Industry in dollars per year .
As a result I have been to many of these factories and I was involved with the original CMP brand ( China Model Products ) and now working with a gentleman to bring that brand back to the USA.
I agree that you need troops on the ground in China in the manner of an office but you also need someone in the actual factory as a worker.
I am not going to bore everyone with business, I can just tell you we have offices all around the globe and we have people in the factories as regular workers.
I know that when MRC secured the VQ line from Thomas it was not a friendly acquisition of distribution rights. Thomas has slipped with some comments in threads that are very revealing.
As far as the brand MRC , they need to review the models based on early consumer reviews and our reviews in in these threads.
I think the two of us and others in this thread are experienced builders so we dont get stressed too easily lol but I have to admit this model has been frustrating.
I finally figured out my rudder issues and it was simply based on using stock supplies from the kit. Today I finally gave up on the push rod “easy connectors “ and soldered on golden clevis connectors. As soon as I tested this modification all of my troubles went away from a sloppy rudder to my servo centering dead on, amazing what good hardware can do.
My suggestions to anyone reading these threads is to simply replace all the hardware and enjoy the model. I would have saved about 8 hours of frustration of I had use aftermarket parts for connectors from day one.
My closing remarks to Motion is that they have to look and take a deep dive into some of the brands they import. We all know the Banana Hobby name in California. Most of us know of their early poor reputation of low quality models. The problem was that BH was importing Starmax brand in the early days when StarMax was total crap.
The problem is that while Starmax was the source of the consumer complaints with Banana Hobby, the bad reputation still fell on Banana Hobby.
That is what regardless of created brands of Nexts, or any created name
Official Nexa 2020mm F8F Bearcat (Balsa ARF) Discussion Thread
Collapse
X
-
Joe,Thanks Jet for the tip.
As far as Motion RC they are by far in my opinion the best RC distributor in the industry so I would never hesitate to buy anything from them. On time shipping, quick, online video education and they actually fly and use RC products. They are so far above the field its silly.
On this model they inherited a good model with bad design elements. I dont know if this model will ever be updated because I am not sure of VQs long term plans.
They seem to have released a ton of smaller models so perhaps the cost is very prohibitive. I also know that the freight out of China has skyrocketed so this could be the problem with the additional cost.
Like you I am also a builder, i have the TF Bearcat, TF FW190 and the Sterling 70” King Cobra waiting in the wings to be built ! So I am not afraid of modifications but flight control related problems are concerning
I would never knock MRC, they’ve never given me a reason to. I only commented on the price, because they know there’s issues with it. As for the cost, I’m with you on the shipping costs rising. Hopefully this year, we’ll see things settle down with our relations with China. COVID19 has caused many problems, and until we get it under control, who knows...
VQ had problems with this model before MRC took it, you can find them on google. But they’ve been producing this model for awhile now, and yet there’s still problems. I think MRC needs a rep on-site to keep these folks on point. I am a huge fan of this scale size in any plane, but especially warbirds. But, I would like to see more “off models” made and not the same ones over and over. The 30/40cc size warbirds are the same models everyone else is making, let’s mix it up. It’s the same in the EDF arena to, as I haven’t purchased a jet from MRC in some time. I have all of their models (all except a couple that I don’t care for), but there’s not much variety. I’m still waiting for an A-7, F-100, F-105, these are great jets and should be made in at least the 80mm (would love all 3 in 90mm) size.
ok, I’m done yapping...Leave a comment:
-
Thanks Jet for the tip.
As far as Motion RC they are by far in my opinion the best RC distributor in the industry so I would never hesitate to buy anything from them. On time shipping, quick, online video education and they actually fly and use RC products. They are so far above the field its silly.
On this model they inherited a good model with bad design elements. I dont know if this model will ever be updated because I am not sure of VQs long term plans.
They seem to have released a ton of smaller models so perhaps the cost is very prohibitive. I also know that the freight out of China has skyrocketed so this could be the problem with the additional cost.
Like you I am also a builder, i have the TF Bearcat, TF FW190 and the Sterling 70” King Cobra waiting in the wings to be built ! So I am not afraid of modifications but flight control related problems are concerningLeave a comment:
-
MRC carries all the sizes, I purchased 4-40 in 48” length.Jet . I am laughing with you not at you , that firewall reinforcement is hilarious, you just like me hahah
. I bought triangle stock and starting on the inside of the box, just waiting to see if my 12 cell set up needs to go into the firewall box.
Question does anyone know where to buy the type pushrods that come with this model ( length wise ) I am considering disassembling my rudder and starting over, I am still not happy with the set up.
I understand your set up , thanks, I am going to see what I can do at this time.
I may add an exterior control arm and run a solid pushrod thru the fuselage direct to the servoLeave a comment:
-
WOW!!!!’
Im glad I purchased it when it was only $750, I feel sorry for the unsuspecting buyer that pays the new price. When they open the box and realize what they got, if it was me, it would be GOING RIGHT BACK!
when got this bird, I got it because I didn’t want to build a kit this winter. But a kit is what I got and I don’t mind a good challenge once in while, but this is OVER THE TOP!
why on earth would they raise the price so much, I thought $760 was a bit much. I guess they need to cover shipping fee increases.Leave a comment:
-
Jet . I am laughing with you not at you , that firewall reinforcement is hilarious, you just like me hahah
. I bought triangle stock and starting on the inside of the box, just waiting to see if my 12 cell set up needs to go into the firewall box.
Question does anyone know where to buy the type pushrods that come with this model ( length wise ) I am considering disassembling my rudder and starting over, I am still not happy with the set up.
I understand your set up , thanks, I am going to see what I can do at this time.
I may add an exterior control arm and run a solid pushrod thru the fuselage direct to the servoLeave a comment:
-
Amen to that!!! I’ve already gone through a bottle of thin CA, just going over the fuse. When I started to install the engine, the firewall box started to come apart. So here’s my answer for that, it’s GOING NOWHERE!!!FYI
Most of the bad glue joints on this build I was able to break by hand including the servo wing blocks all of them, the formers to the left and right of the firewall, all mid fuse formers joints and some wing areas around the landing gear all now reinforced. You know if things aren’t right when you hear wood cracking when you simply grab the fuse to roll it over.
reglue everythingLeave a comment:
-
Now that it’s done, should have taken a couple pics of it. Can’t now, because I used hysol to install the tail gear mod setup. But I had the same play with the servo powered up. So I removed that clevis from nylon arm attached to the rudder shaft. Then I soldered the clevis straight to the rudder shaft. Now it’s direct connection and zero play, well maybe a couple thousands of play.Well after the entire thread I decided to go back and check something on my rudder. I did not like the insertion of the control rod into the rudder.
Without power to the servos I have 1/2 of play in my rudder ( bad ) surly I will get flutter. I was trying to figure out " how did I miss that " . Well, when under servo power and fully extended left or right, i have zero play in the rudder, but when at neutral -center line flying I have a 1/2 of play and I know the rudder will move with normal wind over the rudder.
So back to the drawing board for me, its non-flyable under the current conditions.
So like Jetman, played with the setup for two hours yesterday and I dont have play but now my servo will not return to center because I my ply supports that remove the play are so tight that they impact the servos ability to return to center. What a PITA and yes I agree its a frustrating model. I have been building kits for years and I think I prefer to build a kit then work for two hours on crap !
Then when I went to trial fit the canopy , the plastic screws are not aligned lol, so more mods to realign the screws.
Jetman, I am following your tail mods, but I don’t follow how you attached the servo controls to the rudder ? Can you elaborate please ?
Hope that helps, and I put Robart large round pin hinges in all control surfaces. I couldn’t imagine using the ones it came with, because I saw my plane hurling threw the sky in a right turn, and the ailerons depart the plane.
By the way, the tail gear I used, came from the BH FAIRCHILD 24. In case anyone wants to know...Leave a comment:
-
Good idea vs the stock keepers !
Well one thing went easy and that was the retracts. The gear doors if 100% flush with the wing inset will rub on the stock wheels. So take note on the gear leg connectors and make sure you select the longer one for insert closer to the wheels.
I attached my retainers ( loose ) and played with the doors to see how flat I could get them and clear the wheel. I am happy with the overall fit and know the doors will not impact my trim based on the final fit.
Not sure if these retracts are still for sale, they were the original Bearcat retracts from VQ & appear very robust.Leave a comment:
-
Yea that will do it.
I wasn’t to sure about those nurrled keeper nuts so I just used a regular lock nut and turned it around so the threads are in the locking part of the nut and the a little blue locktiteLeave a comment:
-
Thanks for the pics, I found my problem with the rudder. I had to eliminate each area of a problem to determine the problem.
1) disconnected the rudder -move freely
2) disconnected the tail wheel - moves freely
3) disconnected the servo arm —himmm rods seem to bind at the VQ stock connections to the rods ???
Ok now I am getting somewhere,
I added red LockTight to the small retaining nuts on the bottom of the stock push rod keepers, the red locktight seeped into the retainer and lock it solid.
So when the servos pushes, the retainers push back creating an off from center end point !
So I removed them, started fresh, used epoxy to hold the retailers as security and wala , problem fixed !!!
My anal personally of wanting to secure everything worked against me !
But its now fixed !
Leave a comment:
-
If yo do this mod remember glue only the sleeve not the pin... It has to move slightly!!!Leave a comment:
-
Trying to find a direct fit tube for the 2.5 mm rudder torque rod was shear luck. It was from some China build extra part but it works.
The control rods supplied are heavy and trying to keep the tail as light as possible is essential so as little ballast in the nose requiredLeave a comment:
-
Ahh ok just bend the rod so its perpendicular to the rudder.
Honestly it should be fine unless maybe other things not straight.
Check to see if every thing true.
It should workLeave a comment:
-
I started fresh and confirmed my rudder has 100% friction free movement and the problem is at the Torque rod . I know from my building days to add Vaseline onto the hinge line so glue was not in the connection and the rudder moved freely.
I am going to try a HD pull pull cable on the rudder and scrap the factory torque rod. I studied the option and moved the elevator to factory max settings and I can clear a pull pull cable.
I should have known better and wanted to add a brass rod over the factory torque rod but with the rod being pre-bent that idea was prohibitive.
I just cant settle for the servo not returning to center so I need to reinvent the mousetrap.
I also dont mind the challenges but some many things on this model are sub -par .Leave a comment:
-
FYI
Most of the bad glue joints on this build I was able to break by hand including the servo wing blocks all of them, the formers to the left and right of the firewall, all mid fuse formers joints and some wing areas around the landing gear all now reinforced. You know if things aren’t right when you hear wood cracking when you simply grab the fuse to roll it over.
reglue everythingLeave a comment:
-
I am in agreement with you guys as far as build quality but I have to say that I am rather enjoying the challenges that this bird seems unintentionally offer.
they did change the control horn hardware to hanger 9 and I l already had some of these laying around to test and the held up pretty good. I basically tried to break them but just bent instead.
Pushrod I used factory for rudder and elevator because there pretty stout at 2.5 mm heavier than 4-40 you just need the right fittings. Wings 4-40 rod with safety clevis from Dubro.
As far as the rudder control there aren’t many options because of elevator interaction so I simply took a metric brass tube I had laying around ..... 2.5 mm I’d and inserted that into the rudder and epoxied it in place. Perfect fit for the rudder torque rod no slop. Glue in the hinges but not the torque rod as to allow for slide movement.
End up with a little but not much flex.... not to concerned.
I think my biggest hurdle was the freakin cowl getting everything centered and drilled. Still not done.
Still workin on gear doors and covers just have to paint with matching latex. There primed so will see how it goes.
Also the choke control will be interesting
Leave a comment:


Leave a comment: