Hi Folks,
Anyone out there have a Bowers Flybaby?
Here is link to short video.
Have a look at approx 2mins in to see his scarf flapping in the slipstream.
My drone pilot is getting better all the time.
Enjoy.
Regards
Jonesy
Nexa L-4 Grasshopper Assembly
Collapse
X
-
Hi Folks,
Here is link to a flight with our Grasshopper.
O.S 4 stroke.Looks and sounds great.
Regards
Jonesy
Kinsale
Ireland
Leave a comment:
-
Recently finished L4 build.All good except dowels missing from kit but had some spare.
Flies really well,looks good in air.Used OS Surpass 52 four stroke for motor.1 PhotoLeave a comment:
-
Update CG
Flew today, securing my LIPO better than yesterday, CG=75mm and it flew just great.
Grts HansLeave a comment:
-
Flying
Today I flew my VQ L4.
Used an FMS 14X8 and with 6S my telemetry gave me a current max 47A, Voltage 23.6V=1109watt max power.
Cruising current is between 10-15 amps and reading my watts in flight around 100-150watt.
It was a bit windy and performed CG in flight test, CG was around 70mm.
In flight my LIPO moved a bit backwards so I had a plane slightly tail heavy but I could handle it.
At home I modified my lipo area with a wooden stop for my lipo so it can not move more back for the next flights.
Hopefully tomorrow it will be less wind so I can trim and balance my plane better.
grts HansLeave a comment:
-
About CG
In manual they say CG is 65-70mm form LE.
But I have some thoughts about this, I fly a lot of planes.
But when I fly a plane for the first time, also I fly new planes for fellow club members.
I always keep the 30% rule from LE in mind as a starting point.
For this plane wing has a dept of 27cm, so 30% = 81mm.
Well I will see in first flight with this plane how it will behave in the air.
For me I test this flying straight in the wind high altitude, throttle to zero and see what the glide path is.
I want to see a glide path around 30-45 degree.
A plane with a slight nose heavy CG is good to fly.
grts HansLeave a comment:
-
-
Some thoughts about manual
Bought me this second hand, was not finished completely.
It had some damage but I repaired it allready.
It's an easy build, just put the parts together.
But I noticed during installing wing struts in manual #26 they say 3*15mm screw, but this is wrong.
In fuselage there is a blind M3 nut installed and looking at covering in bright light I found where to puncture covering.
See pics below.
I installed a AL5055-400Kv motor, YEP 100A esc and will use 6S5000 LIPO, prop at the moment is a master airscrew 15 x 10 but I don't know if it will be on there in the future after some test runs.
Grts HansLeave a comment:
-
did you have any problem screwing the self threading 3mm screw into aluminum wing tube ?Leave a comment:
-
I got my built. This plane flies great! I found pictures of the still operating "Mistress". It doesn't have a blue cowl. So I changed mine to match the real plane.Leave a comment:
-
I had the eFlite Power 46 in and it was too much torque and it ground looped. With the 32 is appears to be a more gentle scale like flyer. Rentaroo's video shows what it fly's like with a 32.If you want to eat the sky, then the 46 is the more, but I wanted a more scale flyer.Leave a comment:
-
-
Can I ask why you took the power 46 out? I ask as Im just finishing one up and I put a power 46 in it, did it have anything to do with your mishap?Hello Rentaroo, I have reached out to this thread to continue my discussion with the Grasshopper. I have rebuilt since my mishap, and it is new and ready. I took out the 46 in place of the eFlite Power 32 Outrunner with a 12x8 prop. Looking forward to flying this critter now. I also just purchased the Nexa PA-18 Super Cub Burda 1620mm (63.7") Wingspan - ARF and will put the 46 in that plane instead. I will update the process, but I am ready to rock!
Rentaroo, what size prop did you finally decide on?Leave a comment:
-
Thanks guys. I went with the slot in the bottom of the firewall, after some careful fun with the dremel. Now to get it in the air!
Leave a comment:
-
I actually velcro'ed mine to the left front of the cockpit side wall. Good air and nothing close. Since it is a Spektrum SMART ESC, I can watch the temperature and have set alarms to be safe on my radio.Leave a comment:
-
Hello,Rentaroo and/or Greyfoxvt, where did you guys place your ESC? I've got mine tied to the front of the firewall, but the battery lead is short enough to make connecting to a battery a real trick through that door! I'm not overly fond of cutting/soldering to extend the ESC's battery lead.
I was able to slide my ESC into the slot on the bottom of the firewall. I did use my Dremel to make the slot a little larger. With this small modification, I was able to route the ESC's battery lead far enough into the cabin area to make connecting the battery a simple task. The ESC receives enough air flow in this location to remain cool.Leave a comment:
-
Hello,Hello Rentaroo, I have reached out to this thread to continue my discussion with the Grasshopper. I have rebuilt since my mishap, and it is new and ready. I took out the 46 in place of the eFlite Power 32 Outrunner with a 12x8 prop. Looking forward to flying this critter now. I also just purchased the Nexa PA-18 Super Cub Burda 1620mm (63.7") Wingspan - ARF and will put the 46 in that plane instead. I will update the process, but I am ready to rock!
Rentaroo, what size prop did you finally decide on?
I'm using a Master Airscrew 12x6 wood prop.Leave a comment:
-
Rentaroo and/or Greyfoxvt, where did you guys place your ESC? I've got mine tied to the front of the firewall, but the battery lead is short enough to make connecting to a battery a real trick through that door! I'm not overly fond of cutting/soldering to extend the ESC's battery lead.Leave a comment:
-
Hello Rentaroo, I have reached out to this thread to continue my discussion with the Grasshopper. I have rebuilt since my mishap, and it is new and ready. I took out the 46 in place of the eFlite Power 32 Outrunner with a 12x8 prop. Looking forward to flying this critter now. I also just purchased the Nexa PA-18 Super Cub Burda 1620mm (63.7") Wingspan - ARF and will put the 46 in that plane instead. I will update the process, but I am ready to rock!
Rentaroo, what size prop did you finally decide on?Leave a comment:
-
Thanks Rentaroo. The model I got (2 weeks ago) does have score marks and I think they are very close to your numbers. I stuck the aluminum tube into the motor plate (yes, it fits!) and used that through the cowl to get a rough idea. Once the motor shows up I should be able to get a better look.Leave a comment:


Leave a comment: