Panzer III

[JustDan]

Thank you

[Rubicon99]

I just purchased Taegen all metal Tiger 1
air soft
any recommendations and advice for a beginner as it pertains to battery, controller, gun and any upgrades

I would say drive it and have fun learning what you like and what you would like it to do better. Then focus on how to achieve what you would like it to do better.

[JustDan]

I just purchased Taegen all metal Tiger 1
air soft
any recommendations and advice for a beginner as it pertains to battery, controller, gun and any upgrades

[Rubicon99]

I liked Stanlley's Barrel Smoke unit. DAK doesn't seem to have those. Yes, Stanlley is a nice guy so I want to give him the business. DAK does have the Tamiya to clark adapter socket that Stanlley didn't have so I might order that from them once my unit arrives. I couldn't see where LEGODEI had an Tamiya socket option for the RF receiver. Perhaps I don't know what I am looking at on their Esty website.

LegoDEI does not make a base for either the HL or Tamiya/Clark receivers. The LegoDEI receiver make use of the stock Tamiya type bases when used with Tamiya tanks and Clark’s with Tamiya bases. Otherwise you have to build your own which is not hard.

Being that you will be using a Clark system you can go straight to a full Tamiya Battle System “TBS” (IR receiver, wiring, IR bulb and base in an all inclusive kit) unless you want the low profile aspect of the LegoDEI receiver.

[quitcherbitchen]

I liked Stanlley's Barrel Smoke unit. DAK doesn't seem to have those. Yes, Stanlley is a nice guy so I want to give him the business. DAK does have the Tamiya to clark adapter socket that Stanlley didn't have so I might order that from them once my unit arrives. I couldn't see where LEGODEI had an Tamiya socket option for the RF receiver. Perhaps I don't know what I am looking at on their Esty website.

[Rubicon99]

I bought the Barrel Smoke system and TK40S off of Stanlley at RCTankLegion. They custom make them I think. Stanlley mentioned that the TK board only uses Tamiya. I spent more on the electronics then the tank LOL. On the other hand, the HL 6.0 transmitter and boards may list on Ebay for $37 but those are each prices. Bundled they would set me back almost $80. I rather spend $80 more for a first rate board in a second hand tank. The options on the TK board system seem pretty cool in comparison to the HL and besides, I love to tinker.

The US Clark retailer is in AZ. Basically overnight shipping for western states. Would have directed you to them had I known you were ready to buy. Oh well Stanley is a good guy too.

I think you will like the TK40 it has a lot of “tinkering” potential.

[quitcherbitchen]

I bought the Barrel Smoke system and TK40S off of Stanlley at RCTankLegion. They custom make them I think. Stanlley mentioned that the TK board only uses Tamiya. I spent more on the electronics then the tank LOL. On the other hand, the HL 6.0 transmitter and boards may list on Ebay for $37 but those are each prices. Bundled they would set me back almost $80. I rather spend $80 more for a first rate board in a second hand tank. The options on the TK board system seem pretty cool in comparison to the HL and besides, I love to tinker.

[Rubicon99]

I don't hesitate to take stuff apart, but I understand a lot of people don't. Modelling my whole life. I went to train store recently and was surprised that everything was already put together. No more kits. Owner said "no one has the time anymore to build, they just want to run the train". Building is at least half the fun. Well for me it is. I bit the bullet and bought a TK40 board as I really can't stand the HL transmitter and want to use my Horus. I figured the board can make the tank more realistic as well as function better. I can move the board and radio to another tank if I get really hooked. I also ordered a barrel flash and smoke unit. Now to order one of LegoDEI receivers. How is the receiver hooked into the top of the Cupola? I guess I need an IR emitter too?

Make sure you order the right LegoDEI receiver. Not the one for the HL 6.0 tanks those will not work with the Clark TK40. This is because Clark uses the Tamiya wiring arrangements not the HL.

The base for the receiver is up to you to build or you can use a Clark or Tamiya base but you will have to find one. Generally not hard to find.

There are a few really good installation threads for the LegoDEI receivers here on this forum. Just do a search and they will come up.

Don’t know if the TK40 will be able to handle the barrel smoke system power requirements. Honestly have not seen anyone try it yet as the barrel smoke is a rather new offering by HL.

[quitcherbitchen]

I don't hesitate to take stuff apart, but I understand a lot of people don't. Modelling my whole life. I went to train store recently and was surprised that everything was already put together. No more kits. Owner said "no one has the time anymore to build, they just want to run the train". Building is at least half the fun. Well for me it is. I bit the bullet and bought a TK40 board as I really can't stand the HL transmitter and want to use my Horus. I figured the board can make the tank more realistic as well as function better. I can move the board and radio to another tank if I get really hooked. I also ordered a barrel flash and smoke unit. Now to order one of LegoDEI receivers. How is the receiver hooked into the top of the Cupola? I guess I need an IR emitter too?

[Rubicon99]

I found my turret problem. The barrel support was broken causing the housing to sag enough to hit the little hook in the front of the turret

Good to see you found the problem. Also good to see you took the tank apart👏👏. Many folks are hesitant to do so.

[quitcherbitchen]

I found my turret problem. The barrel support was broken causing the housing to sag enough to hit the little hook in the front of the turret

[Rubicon99]

I use to fly right across the street from the museum at Whittier narrows. I don't have IR yet, but I assume they use HL IR? I am trying to order a TK22A controller that is HL IR and Tayima compatible. The descriptions are hard to figure out want I need to modify in order to make the Clark board work. The TK Clark boards do look backwards compatible with all HL tanks. Clark makes a 6.0 board that upgrades the HL 5.3(which is what my Panzer has) but it looks like only Tayima IR. It means my smoker and everything else is plug n Play. But I don't want to buy it if it doesn't give me HL compatible IR if that is what everyone is using.

The new 6.0 HL tanks are all Tamiya IR compatible. So anything that is Tamiya compatible will be able to take and receive hits from a 6.0 HL tank. There is a thread about this topic on this forum I wrote not long ago. I will see if I can dig it up and bump it to the top for you and a few other to take a look at.

The Ca. clubs base their requirements on having a tank that is at least able to take hit from an authentic “Tamiya brand” IR battle system. Which the 6.0 HL and Clark board tanks can do. Both though do this better with aftermarket quality IR receiver upgrades like the one offered by LegoDEI which many here use.

Both clubs have folks with “loaner” tanks for those that are not quite set up with their own tanks yet to try some battling. I am one of them. So no worries about showing up and not being ready. Folks love having new people attend and give the hobby a try.

[quitcherbitchen]

I use to fly right across the street from the museum at Whittier narrows. I don't have IR yet, but I assume they use HL IR? I am trying to order a TK22A controller that is HL IR and Tayima compatible. The descriptions are hard to figure out want I need to modify in order to make the Clark board work. The TK Clark boards do look backwards compatible with all HL tanks. Clark makes a 6.0 board that upgrades the HL 5.3(which is what my Panzer has) but it looks like only Tayima IR. It means my smoker and everything else is plug n Play. But I don't want to buy it if it doesn't give me HL compatible IR if that is what everyone is using.

[Rubicon99]

Any way to look up tank clubs in So Cal? I am near Los Angeles.

LA Tanks battles at the tank museum in Alhambra the first Sunday of every month when not under the COVID restrictions.

Also San Diego tank club “619 Battalion” does battles 6-8 times a year also when not under COVID restrictions.

I battle with both clubs and they are HL tank friendly.

COVID has really put a damper on battle days with each club because of the location used, not because the memberships are scared of it.

I have a bunch of photos from a few of the club battles on my Instagram @ fsttanks. Feel free to take a look.

[quitcherbitchen]

Any way to look up tank clubs in So Cal? I am near Los Angeles.

[SoCalBobS]

Actually to get free shipping you have to “make an offer”. I usually make whose total eliminates the shipping and maybe $5 or more off from their listed price. You can also ask for parts and such that may not be shown. I lost a 1/2” square part from a tank, my fault for not gluing, and they sent me a replacement free.

Also, if you use HL’s 6.0 transmitters, you can bind more than one 6.0 tank to each Tx. I’ve got three tanks on each Tx, just gotta pick and choose so you don’t end up with two tanks you want to run on the same Tx! 🤪😭

[quitcherbitchen]

When I looked there wasn't any free shipping, but I wish I had jumped on one that I guy had that already had the 360 rotation and metal tracks for $175 free shipping. I paid $150 for mine and the radio is old and it has a missing hatch with a dead battery on arrival. I ordered the 3500 battery from motion this morning. That is an upgrade I can live with as I probably needed more capacity.

[SoCalBobS]

QB, just for future reference, I bought my 6.0 Panzer III Pro from Toucan on eBay for $185, which included metal tracks, sprockets and idlers and free shipping from New Jersey. Keep them in mind whenever you are looking for the next tank!

[Rubicon99]

I powered her up with a spare 7.2 Lipo that doesn't fit the bay but would help me see if it works. She works except the turret gets caught or misses a gear tooth going to the right. Gets stuck and chatters. I am guessing since I haven't opened up the hull that it is getting caught on something.

Most likely you have a few wires getting caught in the turret rotation gear. Also the turret will not turn 360 degrees. More like 320. The clicking you hear is the “slip” gear and it is there to keep the turret gears and motor from get damaged. The barrel has one too for the same reason.

[quitcherbitchen]

I powered her up with a spare 7.2 Lipo that doesn't fit the bay but would help me see if it works. She works except the turret gets caught or misses a gear tooth going to the right. Gets stuck and chatters. I am guessing since I haven't opened up the hull that it is getting caught on something.