Walterson's Motors and Transmissions

Collapse
X
Collapse
First Prev Next Last
 
  • Time
  • Show
Clear All
new posts

  • Jeffprockl1962@gmail.com
    replied
    I haven't put either one of them on my RPM meter to check how fast those Motors run yet I don't believe the red motor is going to work I think they're too big but right now I'm in the middle of something else the walterson's come with three different opinion years the one in the picture is is the smallest opinion gear so anything above that will just like you say make you go faster and faster. I have a brand new set that's never been run of the waltersons which is all going to that Panther G when I do it. I'll let you know when I do an RPM check on those Motors though talk to you soon bye.

    Leave a comment:


  • keilau
    replied
    Originally posted by Jeffprockl1962@gmail.com
    The waltersen's motors on these transmission kits are 380, and yes you are right they are low RPM. I'm disabled and on days when I'm not out messing around with things like those 6x6s I can sit around and mess around with different things like this I really don't know if those red Motors are going to work or not what's real nice is the waltersens comes with the tool kit that has pulley pullers on it and stuff I don't know if they'll work or not I was just going to give it a shot just for the heck of it this is an old set of Transmissions and they're kind of noisy. As far as breaking on the red Motors that power source that they're sitting on top of by the way that makes those red Motors look really big it's just cuz they're forward of the Boston's Transmissions when I took that picture, I break them in and water real slowly and then I'll bring the RPMs up and down and put them in reverse and do them equally that way and but I've always broke my brush motors in in water. Then I clean them out with electrical contact cleaner then WD-40 to get any water out of it and then a dielectric silicone spray for the bearings. It's just one of those things I'm playing around with, and all the input I get from you guys helps also cuz you guys have been doing this a lot longer than I have been!
    How slow is the Walterson motor's RPM? The Tamiya 380 runs at 18000 and the Red390 at 26000 which may be too fast for the Walterson gearbox. You will need a reduction gear ratio of 56 or higher for the Pather G tank with these high RPM motors. The gearbox should have tight ball bearing spec and little play of the gears. The Heng Xin or Taigen/Torro gearbox meet the requirements.

    Leave a comment:


  • Jeffprockl1962@gmail.com
    replied
    This Auto spell! Walterson's not boston's!

    Leave a comment:


  • Jeffprockl1962@gmail.com
    replied
    The waltersen's motors on these transmission kits are 380, and yes you are right they are low RPM. I'm disabled and on days when I'm not out messing around with things like those 6x6s I can sit around and mess around with different things like this I really don't know if those red Motors are going to work or not what's real nice is the waltersens comes with the tool kit that has pulley pullers on it and stuff I don't know if they'll work or not I was just going to give it a shot just for the heck of it this is an old set of Transmissions and they're kind of noisy. As far as breaking on the red Motors that power source that they're sitting on top of by the way that makes those red Motors look really big it's just cuz they're forward of the Boston's Transmissions when I took that picture, I break them in and water real slowly and then I'll bring the RPMs up and down and put them in reverse and do them equally that way and but I've always broke my brush motors in in water. Then I clean them out with electrical contact cleaner then WD-40 to get any water out of it and then a dielectric silicone spray for the bearings. It's just one of those things I'm playing around with, and all the input I get from you guys helps also cuz you guys have been doing this a lot longer than I have been!

    Leave a comment:


  • keilau
    replied
    Originally posted by tank_me
    Looks like the Wathersons have the black 380s, not 540/550s.
    If so, the internally fan cooled Red390 will be a good move.

    In the picture, the black motors seem to have a larger diameter than the Red390. A measurement of the OD of the Walterson motor case can easily clarify that. The large motor drive gear also makes me suspect the Walterson motor were low rpm motors.

    Leave a comment:


  • tank_me
    replied
    Looks like the Wathersons have the black 380s, not 540/550s.

    Leave a comment:


  • keilau
    replied
    Originally posted by Jeffprockl1962@gmail.com
    In case some of you have never seen these or heard of them before these are walterson's Transmissions supposed to have heavy duty magnets and windings in the motors and they're all brass gears anyhow I'm going to try and put these hen long red motors on them ought to be interesting. Click image for larger version  Name:	20230824_125430.jpg Views:	0 Size:	61.1 KB ID:	384947 Click image for larger version  Name:	20230824_125118.jpg Views:	0 Size:	71.3 KB ID:	384948 Click image for larger version  Name:	20230824_125250.jpg Views:	0 Size:	73.2 KB ID:	384949
    Are the waltson motor 540 motors? What motivates you change them to HL red390 motors? The Red390 is a good upgrade from HL Grey380, but will be a step down from 540. The waltson motor has much larger drive gear than the HL 380/390 series. The red 390 does not look like a dropin replacement.

    I use 3 pairs of the HL Red390 and one pair MaxFan390. The internal fan and axial ball bearings keep them running much more stable, quieter and cooler than the HL grey380. All 4 pairs of 390 have consistent performance on the bench. However, some forum members reported melt down (physically) of their Red390. They never identified the source of the problem. I suspect that those may be low quality imitator of the HL Red390, but I cannot rule out completely a quality control issue by HL.

    After I install the 390 motors on my tank, I run the motor at full speed. The motor case temperature stablize in about 10 minutes and does not exceed 20 degrees F above ambient. Then, I know for sure I get a good motor.

    Leave a comment:


  • Jarlath
    replied
    Originally posted by Jeffprockl1962@gmail.com
    Just for fun can anybody tell me what this drivetrain is? Click image for larger version

Name:	20230815_095933.jpg
Views:	1305
Size:	108.3 KB
ID:	384955
    Looks like an Argo interior?

    Leave a comment:


  • Jeffprockl1962@gmail.com
    replied
    Aatv?

    Leave a comment:


  • Jeffprockl1962@gmail.com
    replied
    Okay Commander Cody, I'll give you a hint it's not a hot rod lincoln!

    Leave a comment:


  • cmdrcody
    replied
    Centrifugal pulley drive-belt system. (ATV?)

    Leave a comment:


  • Jeffprockl1962@gmail.com
    replied
    Just for fun can anybody tell me what this drivetrain is? Click image for larger version

Name:	20230815_095933.jpg
Views:	1305
Size:	108.3 KB
ID:	384955

    Leave a comment:


  • Jeffprockl1962@gmail.com
    replied
    Oh and I'm going to try them out in this full metal henlong tiger one. Click image for larger version

Name:	20230803_130852.jpg
Views:	408
Size:	71.7 KB
ID:	384953

    Leave a comment:


  • Jeffprockl1962@gmail.com
    replied
    In case some of you have never seen these or heard of them before these are walterson's Transmissions supposed to have heavy duty magnets and windings in the motors and they're all brass gears anyhow I'm going to try and put these hen long red motors on them ought to be interesting. Click image for larger version

Name:	20230824_125430.jpg
Views:	1325
Size:	61.1 KB
ID:	384947 Click image for larger version

Name:	20230824_125118.jpg
Views:	477
Size:	71.3 KB
ID:	384948 Click image for larger version

Name:	20230824_125250.jpg
Views:	431
Size:	73.2 KB
ID:	384949

    Leave a comment:


  • keilau
    replied
    Originally posted by Jeffprockl1962@gmail.com
    Does anyone know if those blue motors from henlong are worth a darn? I have an all-metal Sherman that I'd like to upgrade the motors and apparently the red ones won't work and I saw some blue ones on AliExpress which are probably fakes, any I was looking for a different type of motor to put in it. I was going to send some pictures of my tanks except for I cannot figure out how to do it on this site whatsoever. Talk to you later Jeff
    The best 380 motor commercially available for hobbyist is the Tamiya GP 380. It has more torque and runs cooler than the Heng Long grey and blue 380 motors. You can search for the "red and blue motor" thread to find more details and test results.

    Click image for larger version

Name:	IMG_5112.jpg
Views:	581
Size:	87.3 KB
ID:	383377
    The Tamiya 380 drives the ball bearing Heng Xin gearbox with excellent results.

    Leave a comment:


  • Rubicon99
    replied
    Originally posted by Jeffprockl1962@gmail.com
    Does anyone know if those blue motors from henlong are worth a darn? I have an all-metal Sherman that I'd like to upgrade the motors and apparently the red ones won't work and I saw some blue ones on AliExpress which are probably fakes, any I was looking for a different type of motor to put in it. I was going to send some pictures of my tanks except for I cannot figure out how to do it on this site whatsoever. Talk to you later Jeff
    Depends on what you are trying to achieve with them?

    Leave a comment:


  • Jeffprockl1962@gmail.com
    replied
    Does anyone know if those blue motors from henlong are worth a darn? I have an all-metal Sherman that I'd like to upgrade the motors and apparently the red ones won't work and I saw some blue ones on AliExpress which are probably fakes, any I was looking for a different type of motor to put in it. I was going to send some pictures of my tanks except for I cannot figure out how to do it on this site whatsoever. Talk to you later Jeff

    Leave a comment:


  • cmdrcody
    replied
    Originally posted by Jeffprockl1962@gmail.com
    No I'm sorry Mr johnson, I thought you knew! No all of my tanks are heng long. Some are modified, some stock. Does anybody have any idea if one was to take the pinion gear and make it really big would that make it go really fast? I have a couple extra holes and Transmissions I wanted to mess around with. It's just a thought. Thank you for your time Fellers Jeff
    You would be applying too much resistance on the motor causing them to use too much current and shortening both motor and battery life.

    Leave a comment:


  • Jeffprockl1962@gmail.com
    replied
    No I'm sorry Mr johnson, I thought you knew! No all of my tanks are heng long. Some are modified, some stock. Does anybody have any idea if one was to take the pinion gear and make it really big would that make it go really fast? I have a couple extra holes and Transmissions I wanted to mess around with. It's just a thought. Thank you for your time Fellers Jeff

    Leave a comment:


  • RichJohnson
    replied
    What brand tanks are your shermans? Need to know before suggestions are made.

    Leave a comment:

Working...