Official FlightLine RC 1600mm F7F-3 Tigercat Thread

[rifleman_btx]

I think that would be impossible because I put some foam tac on the square plug that keys into the fuse

Awe damnit... :(

[Grossman56]

Never thought of using gorilla glue on MRC building video they used foam tac. I am going have to fill the gap because I can't afford another $100 for a replacement fuse and tail section hopefully it will hold together.

Hi Mad Baron, I had the same trouble with the 1600 mm Spitfire, the tail came loose twice! Finally went 5 minute epoxy. I did use Foam-Tac on the Tigercat, just lucked out I guess.
Grossman56

[Mad Baron]

I think that would be impossible because I put some foam tac on the square plug that keys into the fuse

[rifleman_btx]

Worst case if you can take a hobby knife and get the tail pulled off then redo the whole process with the gorilla glue. :Confused:

[Mad Baron]

Never thought of using gorilla glue on MRC building video they used foam tac. I am going have to fill the gap because I can't afford another $100 for a replacement fuse and tail section hopefully it will hold together.

[OV10]

I did use a thin bead on the tail part I put it together and pulled it apart and reassembled it but it separated at the top.

You originally commented on using a "generous amount" thus the reason for my suggestion.
I personally don't use Foam-Tac on structures that are under load like airfoils and firewalls.:Scared:
Want that Gorilla seeping into those foam nooks-n-crannies and forming a solid foam weld.:Cool:

[Mad Baron]

What most folks don't realize about Foam-Tac(or any other foam adhesive) is that using copious amounts is actually not a good thing.
More goop does not make for a stronger joint and all that extra actually can start to melt pockets/holes in the foam seam.
Best practices for application:
Apply in thin smooth continuous bead on one surface.
Put both mating surfaces together to apply the adhesive bead to other surface which creates like an adhesive gasket.
Pull the mated surfaces apart about 1/2 inch to allow air to start to firm/set glue for a couple minutes.
Re-mate the surfaces and hold or tape together for a minute or two.
If you don't want an elastic joint, white Gorilla is your next best foam modeling friend.;)

I did use a thin bead on the tail part I put it together and pulled it apart and reassembled it but it separated at the top.

[Hardway]

I am really starting to hate this plane. the tail is separating from the fuse even though I used a generous amount of foam tac. I wish I sent it back when I got it.

:(:(:Straight-Face: Sorry

[OV10]

I am really starting to hate this plane. the tail is separating from the fuse even though I used a generous amount of foam tac. I wish I sent it back when I got it.

What most folks don't realize about Foam-Tac(or any other foam adhesive) is that using copious amounts is actually not a good thing.
More goop does not make for a stronger joint and all that extra actually can start to melt pockets/holes in the foam seam.
Best practices for application:
Apply in thin smooth continuous bead on one surface.
Put both mating surfaces together to apply the adhesive bead to other surface which creates like an adhesive gasket.
Pull the mated surfaces apart about 1/2 inch to allow air to start to firm/set glue for a couple minutes.
Re-mate the surfaces and hold or tape together for a minute or two.
If you don't want an elastic joint, white Gorilla is your next best foam modeling friend.;)

[rifleman_btx]

Damn... :(

[Mad Baron]

I am really starting to hate this plane. the tail is separating from the fuse even though I used a generous amount of foam tac. I wish I sent it back when I got it.

[Grossman56]

I went to pick it up and bumped it and before I could catch it one of the main wheels fell of the table and snapped the gear door off. I think I'm going to walk away from it for a while since I'm upset with it.

Easy big Fella!!
I had a ladder fall off the wall and come down on the tail of mine. I couldn't believe that all it did was a slight ding in the vertical stab's leading edge. Out with the foam filler and good as new. She lives a charmed life.

Grossman56

[Hardway]

I have an extra gear door set if you need it!! Sorry that happened...

[Mad Baron]

umm.. are you saying that it rolled off? I hope it wasn't smashed up... that sucks.

I went to pick it up and bumped it and before I could catch it one of the main wheels fell of the table and snapped the gear door off. I think I'm going to walk away from it for a while since I'm upset with it.

[Hardway]

Along with getting the garage rebuilt ;)

Sending thoughts and prayers to you and you family Bro!!! For blessings in everything ya'll do in the future!!! :Cool::Cool:

[OV10]

After your little girl get's hitched, you'll just have to get started on the 83" Tigercat:Cool:

Along with getting the garage rebuilt ;)

[Hardway]

here is a pic of mine after assembly right before it rolled off the table

:(:( Status??

[themudduck]

here is a pic of mine after assembly right before it rolled off the table

umm.. are you saying that it rolled off? I hope it wasn't smashed up... that sucks.

[Twowingtj]

Only problem I had on the Tiger and Lightning was that foam don't tolerate incineration at all :Scared:

After your little girl get's hitched, you'll just have to get started on the 83" Tigercat:Cool:

[rifleman_btx]

Man that still tears me up about that damn fire bro. :(