.png)
Thanks Steve! Happy Thanksgiving to you as well.
-
-
Merry Christmas all!
Finally got around to another round of tests with 100% FSA exhaust and enlarged intake cheater. Overall, improvements were relatively minor, with 600g of thrust at 618W compared to 590g at 596W. 10 grams of increased thrust with the changes.
Earlier this week I quickly went out to confirm ease to hand-toss. below is a short video from the first of the 2 flights. I forgot to write down notes from the maiden, so I was re-learning a bit with what rates I had set for ailerons, rudder, and elevator. The plane felt a bit snappier than before when banking using ailerons with a bit of rudder, so I brought it down pretty quickly in the video. Besides, this, the plane takes off from an underhand toss pretty easily.
I have graphics coming in from Callie in the next week or 2, so I will have some photos to share of a completed U-2R and ER-2. I'm also going to try and vacuum from canopies for both airframes. Ordering some 1300mAH 4S packs as well.
Comment
-
Merry Christmas to you as well! Looks greatComment
-
Callie graphics came inComment
-
Hey Steve,
I will be just doing a sanding of the printed parts with no additional paint. I have one in black and one in white. Just basic gap filling with ABS slurry where its needed, and then matte or satin clear coats to seal in the vinyl and make it easier to wipe down from grass or dirt stains.Comment
-
Trying out airfoil analysis using XFLR5. Still a ways to go to understand what I am looking at, but hoping to be able to use this to optimize my scratchbuild and 3d print designs. After I figure it out and learn on the U-2R, I'm going to revisit my A333 and see how well or inefficient I designed that wing.Comment
-
3D printed lading gear set added, included printed rubber tires. Can be installed/removed with a set of screws for the mains and tailComment
-
WOW !
Mike\"When Inverted Down Is Up And Up Is Expensive\"Comment
-
Beautiful work! That looks awesome! You never cease to amaze me at what you’ve been able to do with 3D printing!Comment
-
Thanks guysComment
-
A fresh fuselage for the original prototype's electronics. Graphics by Callie.Comment
-
Nice.
Mike\"When Inverted Down Is Up And Up Is Expensive\"Comment
-
I grew up close to Davis-Monthan AFB in Tuscon, these black ships were a constant sight in the skies above me. Very impressive in the air with a distinctive whistleComment
-
I still see them about once a week flying out of Osan, almost got ran over by one twice back in 2013. I was flying a Cessna 172 with the flying club, and apparently competing for traffic pattern time with a U-2. After almost being ran over the second time I realized that the tower controller that day was an idiot, and so I called it, and came in too land.
Comment
-
Duuuude, how cool is this?!?Comment
-
Hey Y'all, This is a great video on the history of the "Black Planes" and the Lockheed Skunk Works. Well worth the watch. Best, LB"I am having an extraordinary ordinary life."~Lucky B*st*rd~
"Find satisfaction in the process rather than an outcome."~Anonymous~
AMA#116446Comment
-
Thanks for sharing the vid. For those who enjoy reading, here was a book I read and can recommend:
"Skunk Works: A Personal Memoir of My Years of Lockheed" by Ben R. Rich and Leo Janos
I also thought I can show a little teaser of another project. Black planes have their own challenges with both EPO and PLA, and ABS has manufacturing challenges as well with 3D printing in hobbyist levels with sections over 100mm. We'll see after I finish my buckeye if I can get another iconic plane to work out.Comment
-
You're doing a T-2 Buckeye? SWEET! I loved flying that plane.Comment
-
Sized for a 90-100mm, Getting to printing it shortly after I make some final scale tweaks to the model that I overlooked originally.Comment
Comment