Some will disagree, however this is my opinion.
The benefit to outward rotation on electric twins is inherent down-thrust created and proportional...
298 results in 0.0227 seconds.
-
Next I added the MG ammunition feed tray parts and the front hinged plates. After adding those, the reinforcement pieces and the M60, the original mounting...
Leave a comment:
-
So how in the world did you get the battery straps strapped down? I can’t even get my fingers in there to tighten or undo them as there is no access...Leave a comment:
-
That sounds like the best of both worlds!!!
...
Leave a comment:
-
I'm using the M2 gun shield from the AHHQ kit because it has the mounting bracket already and fits with a little modification.
...Leave a comment:
-
Thank you very much, Tdriver113 for sharing the link with me. I have to go out for a while, I'll check out your Vietnam Gun Truck build when I get ho...Leave a comment:
-
The original plan was to place the main board in the front above the drive motors. The speaker is mounted in the fuel tank and a new smaller battery from...Leave a comment:
-
It's here in the RC truck section. The project is on hold until I figure out a good decal source for a name to go on the sides.
https://...Leave a comment:
-
Looking at these events brings me back to the Mustang Car Club and all the car shows we had every summer. Those were the days!!!!!!!
Leave a comment:
-
Those tacos Carlos made make me hungry looking at the photos of them.
Tanks & Tacos!!! What a combination!!!!!...
Leave a comment:
-
David, what a great event, I'll bet everyone had a fun day....
Leave a comment:
-
Did Chris and the Motion team mention which turbine size (X40, or SW80) they will make the F35C for. I know that the Zeus is only for X40. Thanks.Leave a comment:
-
Thanks for the update! Nice to hear you like how it flies once you got things sorted out and like you said, this is without a Gyro. The guys here... mention...Leave a comment:
-
Most twins with opposite rotation props rotate inwards at the top, unless there is a good performance or aerodynamic reason to do it differently....Leave a comment:
-
Tdriver113, do you have a build thread for your Vietnam Gun Truck on this site? If so, I'd like to check it out. If not, feel free to share a few images...Leave a comment:
-
Driver, you're doing a great job making you M113 represent the actual full scale version. If I could like your thread I certainly would if I could figure...Leave a comment:
-
You're like me, I'll use anything to scratch build with that's priced well and gets the job done!!!...
Leave a comment:
-
I agree it's best for indoors. I like it because it's nicely detailed as a model kit would be with the added benefit of it being RC. It looks great with...Leave a comment:
-
Hi Nick. Yessir. Successful maiden, but barely. I used a 3s 1500mah, and per the manual setup the girl was veryyyyyy tail heavy. Battery all the way...Leave a comment:
-
Did you get to maiden it!?...Leave a comment:
-
I am not missing it at all, just curious. The M16 half-track in 1:16 scale is basically an indoor RC model. I prefer the full track tank for outdoor ...Leave a comment:
-
OK, I was able to upload a few more videos, so here's all the RC wheel hubs turned, and the beginning of the you could call them Donuts, or washers, whatever...
Leave a comment:
-
Thanks Dave, just what I needed. Setting up the Spektrum from Futaba is a little different. Learning new things. I have been flying a E-Flite 1.5 Air...Leave a comment:
-
Hi Rex: just saw your entry. All my FMS P-47s CG'd around the same area. Even the heavily modified bubbletop was in the same area as all the other stock...Leave a comment:
-
Interesting detail I hadn't noticed before; tracks are different. NF has put a lot of detail into their offerings.Leave a comment:
-
Thanks fru ausie, I'll look it upLeave a comment:
-
The inside ramp panel from the AHHQ kit is almost a drop in. A slight trim on the sides and bottom and it slides right in. That and the door panel were...
Leave a comment:
-
The small patch is similar to the actual door mount.
...Leave a comment:
-
The first thing I did today was to take some better photos of the RC wheel hubs I'm modifying. Here's some images and a video to explain what's being...
Leave a comment:
-
Good morning everyone!!! The last image I posted yesterday night, the hub wasn't deburred, and it's not the best image. Last night, I measured across...
Leave a comment:
Leave a comment: