Official FlightLine 1600mm B-25J Mitchell PNP Thread
Collapse
X
-
That's what I'm talking about! 😎 Is that the older FMS B-25? If so very nice job on the conversion! I was thinking about carving a one off nose from balsa or foam but after reading through the thread and seeing a lot folks saying that they're having to move their battery as far forward as possible, I was thinking a 3D printed or fiberglass nose might help (not trying to add 'dead' weight). I was excited to learn of Fast N Light's efforts as today a 3D printed nose would be more practical but I'm more familiar with the fiberglass route. I've been gathering all the info I can find on the 8-gun noses. I sure wouldn't have wanted to be on the PO'd end of 14 - (with the top turret swung forward) .50 cal. machine guns pointed my way! -
-
Leave a comment:
-
Same here. CG is good as marked. Depends on battery size and weight of course. I measure mine gear down right side up (since it is a mid-wing).Leave a comment:
-
I'm sure it has been covered here somewhere in the many previous pages ... just want to check to see if the CG location as noted in the instructions (and the mark on the bottom of the wings) is good ?
Thanks.Leave a comment:
-
I've put a few dozen flights on my B-25. I absolutely love her! She flies great and is really easy to land (provided that full flaps are used). With that said, though, I think that what has impressed me the most about this B-25 is its robust landing gear. My landings are good, generally speaking, but I have carrier-landed her a few times. The gear has absorbed those hard landings well and has shown no signs of bending or warping. Plus, the gear box hasn't pulled out of the wing on any of those rough landings.
Kudos to Motion and Flightline for putting robust gear in this toy airplane. Great aircraft!!!Leave a comment:
-
Ha! Yeah, maybe just a little. My maiden landings tend to be a bit faster and longer than I normally prefer.
Leave a comment:
-
-
OUTSTANDING! :clap: Now that's a runway I could get into! Definitely not a Beach of a runway like you had before, but I'm sure you miss the basketball hoops, light poles and kids playing in the field. Although I can't see how your going to execute those long 3 point shots into the net you're known for!Had a great maiden without issues! She's a pu$$ycat as everyone has reported. I feel so spoiled now flying at the ocean. At low tide, the compact sand is the perfect, smooth, endless runway. The backdrop doesn't hurt too! Takeoff was without incident. You know within seconds of liftoff if a model is going to be a pu$$ycat or a bear. Luckily she falls into the former category. Needed some trimming here and there but otherwise was extremely docile. Landing was a non-event. Flaps, floated in, gentle flare and touchdown. The crowd approved, lol.
I'll post a short video tomorrow.
Leave a comment:
-
Had a great maiden without issues! She's a pu$$ycat as everyone has reported. I feel so spoiled now flying at the ocean. At low tide, the compact sand is the perfect, smooth, endless runway. The backdrop doesn't hurt too! Takeoff was without incident. You know within seconds of liftoff if a model is going to be a pu$$ycat or a bear. Luckily she falls into the former category. Needed some trimming here and there but otherwise was extremely docile. Landing was a non-event. Flaps, floated in, gentle flare and touchdown. The crowd approved, lol.
I'll post a short video tomorrow.
Leave a comment:
-
Be sure to calibrate the ESC's. Almost crashed mine on the first flight because of both motors not spinning at the same RPM's. Good luck!Leave a comment:
-
Alright all you B-25 experts, I am about to maiden mine this morning at the beach. Got her all ready to go but before I head out in some hours from now, I would love if anyone could pitch in really quick to provide me with any tips and tricks before the maiden? Much appreciated!Leave a comment:
-
Bob,
You had mentioned that scenario and will look forward to that.
I have started designing a draft from drawings and photos, however, I have not taken any exact measurements from the model to scale it.
The shape is simple enough, even without any frame structure and at the attach point it roughs out at 25 degrees off 90 degrees in side view by my eyes.
I'll post the design once completed for your review. and comment.
Best, Steve
Leave a comment:
-
Thanks! You can see the tail cone I vacuum formed for the FMS version. Maybe I can use the mold as a basis for the FL version.borntoolate, now that's what I'm talikin' about! Good lookin' C model for certain. Bravo Zulu, Sir. Best, LB
BobLeave a comment:
-
borntoolate, now that's what I'm talikin' about! Good lookin' C model for certain. Bravo Zulu, Sir. Best, LBLeave a comment:



Leave a comment: