I started off by taking a light cut...
292 results in 0.0089 seconds.
-
I spent about 5 hours today to finish modifying AHHQ's kit wheels to use them for my M8 RC conversion.
I started off by taking a light cut... -
This is one of the Gun Truck videos I watched. https://www.youtube.com/watch?v=vvquQC7h8hM&t=191s
Here's another great video on Commietube....Leave a comment:
-
Don't forget the ole Budweiser cases!!!!! Afterall, it made Bud Wiser!!!!!!!!!
GI's had to unwind after they went through the shooting gallery and...
Leave a comment:
-
Tdriver113, I really this build. I've always wanted a 1/16 WW-II 4x4 weapons carrier, and it's only a 1/35th scale model kit. I purchased the closest...
Leave a comment:
-
The construction of the bed with the added battery box is well done. I've watched a couple of videos about these modified gun trucks a while back on Youtube....Leave a comment:
-
I'm using some of the WPL parts in my AHHQ M8 Greyhound RC conversion....Leave a comment:
-
Hi All, I can see that it has been a few years since there was action on these pages.
I just picked up one of these. - Wow, what a plane....Leave a comment:
-
Tdriver113, I hope you don't mind me saying this but, I'm thinking, either you're a Vietnam Vet, or maybe your Dad, or an uncle was because of your interest...Leave a comment:
-
Tdirver113, As often as I can, I like to add screws to make what was a static detail become movable details just as you have done here.
...
Leave a comment:
-
I did a test fit of the leftover hull floor section from the AHHQ kit turned into my modular set up. Room for the board, speaker, and my blue tooth speaker...
Leave a comment:
-
Battle Day announcement for July:
Kinda late notice. Been really busy lately. The next battle day is taking place on Saturday July 18th,...Leave a comment:
-
The replacement shoulder screws arrived today. I ordered 2 different sizes to see what would fit best because the measurements were so close. One was...Leave a comment:
-
I think those settings should give you a safe start, anyway, and you can adjust them to your particular style of flying. I took up my Corsair for a couple...Leave a comment:
-
Some will disagree, however this is my opinion.
The benefit to outward rotation on electric twins is inherent down-thrust created and proportional...Leave a comment:
-
Next I added the MG ammunition feed tray parts and the front hinged plates. After adding those, the reinforcement pieces and the M60, the original mounting...
Leave a comment:
-
So how in the world did you get the battery straps strapped down? I can’t even get my fingers in there to tighten or undo them as there is no access...Leave a comment:
-
That sounds like the best of both worlds!!!...
Leave a comment:
-
I'm using the M2 gun shield from the AHHQ kit because it has the mounting bracket already and fits with a little modification.
...Leave a comment:
-
Thank you very much, Tdriver113 for sharing the link with me. I have to go out for a while, I'll check out your Vietnam Gun Truck build when I get ho...Leave a comment:
-
The original plan was to place the main board in the front above the drive motors. The speaker is mounted in the fuel tank and a new smaller battery from...Leave a comment:
-
It's here in the RC truck section. The project is on hold until I figure out a good decal source for a name to go on the sides.
https://...Leave a comment:
-
Looking at these events brings me back to the Mustang Car Club and all the car shows we had every summer. Those were the days!!!!!!!
Leave a comment:
-
Those tacos Carlos made make me hungry looking at the photos of them.
Tanks & Tacos!!! What a combination!!!!!...
Leave a comment:
-
David, what a great event, I'll bet everyone had a fun day....
Leave a comment:
-
Did Chris and the Motion team mention which turbine size (X40, or SW80) they will make the F35C for. I know that the Zeus is only for X40. Thanks.Leave a comment:
-
Thanks for the update! Nice to hear you like how it flies once you got things sorted out and like you said, this is without a Gyro. The guys here... mention...Leave a comment:
-
Most twins with opposite rotation props rotate inwards at the top, unless there is a good performance or aerodynamic reason to do it differently....Leave a comment:
-
Tdriver113, do you have a build thread for your Vietnam Gun Truck on this site? If so, I'd like to check it out. If not, feel free to share a few images...Leave a comment:
-
Driver, you're doing a great job making you M113 represent the actual full scale version. If I could like your thread I certainly would if I could figure...Leave a comment:
-
You're like me, I'll use anything to scratch build with that's priced well and gets the job done!!!...
Leave a comment:
Leave a comment: