Originally posted by Woodcock
View Post
Announcement
Collapse
No announcement yet.
Official FlightLine 850mm P-51D Mustang Thread
Collapse
X
-
This one comes with torque roll for the hand tosses so be sure not to go full WOT or 3/4 power on the throw or she will torque in. Ask me how I know.
I apply about 50% power tops and underhand toss her with about 30 degrees skyward and have a touch of right stick to counter the torque roll...Not perfect, but once she's up and you have both hands on the sticks she's just a ball.
Also, I found the stock props especially brittle and broke 3...2 were hard landings and one just broke for no reason I could tell. So I swapped them out for a 9x6 APC. MUCH better. No matter the landing, those props just resist breaking.My YouTube RC videos:
https://www.youtube.com/@toddbreda
- Likes 1
Comment
-
Well, Xmass came early to my house this year :D
Guys, I've got a DX 8 and a Admiral rx600 gyro receiver, of which I dont know squat.
I learn to fly on my beloved Carbon Cub S+, which I got as RTF, so it was just plug and play.
Any advice on how to setup my TX and receiver?
Much obliged1 Photo
- Likes 2
Comment
-
Guys, Im having a challenge with my Mustang. I assemble the plane, install Admiral Gyro Rx600 receiver and bind it to my Spektrum DX8.
Thing is, I have zero throttle response, with my stick movement.
I also tried to programme ESC, following the video James provided, but still got zero throttle.
Aileron and elevators work just fine.
Any idea what is going on?
Tnx
Comment
-
Check to make sure your throttle lead polarity is correct...Also, if there's a BEC lead you want to make sure you have that plugged into an open port on your receiver. Also, check to make sure your motor/ESC connections are all connected and tight. Hope that works!My YouTube RC videos:
https://www.youtube.com/@toddbreda
- Likes 1
Comment
-
Originally posted by Aros View PostCheck to make sure your throttle lead polarity is correct...Also, if there's a BEC lead you want to make sure you have that plugged into an open port on your receiver. Also, check to make sure your motor/ESC connections are all connected and tight. Hope that works!
Next is maiden, weather permit.
Just one quick question for the guys using the Admiral 600x Gyro, which combo select are you using on take off? Is it better to use combo C ( GYRO ON), or combo A, while holding recovery button?
I plan to underhand toss it, with 50% throttle.
Cheers
- Likes 1
Comment
-
Originally posted by Mr.Black View Post
Thank you Aros, but I already find the solution. I didnt follow the procedure to initialize ESC on the plane, now im good.
Next is maiden, weather permit.
Just one quick question for the guys using the Admiral 600x Gyro, which combo select are you using on take off? Is it better to use combo C ( GYRO ON), or combo A, while holding recovery button?
I plan to underhand toss it, with 50% throttle.
Cheers
Comment
-
Originally posted by Deadpool View PostI underhand toss it with about 60% throttle 75 to 80 degree angle with the gyro on, and fly away (motion RC Admiral RX600SP).
Did you have to put any elevator/rudder input or it flies away by itself?
Guys I broke 4 props on 4 flights and broke the nose of the plane.
Luckily its foam so its fixable, but I getting tired of launching and crashing this plane. Flying itself is breeze. Its my first Warbird, and I really love it, but launching is whole diffrnet game, at least for me.
- Likes 1
Comment
-
Originally posted by Aros View PostThis one comes with torque roll for the hand tosses so be sure not to go full WOT or 3/4 power on the throw or she will torque in. Ask me how I know.
I apply about 50% power tops and underhand toss her with about 30 degrees skyward and have a touch of right stick to counter the torque roll...Not perfect, but once she's up and you have both hands on the sticks she's just a ball.
Also, I found the stock props especially brittle and broke 3...2 were hard landings and one just broke for no reason I could tell. So I swapped them out for a 9x6 APC. MUCH better. No matter the landing, those props just resist breaking.
Also, where did you bought this props?
I alredy brake 4 flightline props. They are rubbish.
Comment
-
I haven't tried on 3S but I would probably go with 60% power on 3S... Here's a link to the prop...I bought 3 and have only needed the 1 so far.
Thin Electric Use LPAR06E adapter rings Includes one set of rings from LPAR06E The material is the same fiberglass composite used in our grey props, just the color is black
My YouTube RC videos:
https://www.youtube.com/@toddbreda
Comment
-
Hello, everyone. New to this site and I'm not sure if this is where i should post this, but who knows, I'll give it a try. I was given a Ferocious Frankie P-51 Mustang that has some damage. I don't know if it crashed or something else happened to it, because the tail section, with the flaps, is what' messed up. there is no battery or remote.. The only reason i kept it is because it just looks so Damn Cool. Anyway I'm not going to go buy a battery and a remote just to crash. If anyone is interested in it for parts. This is what's printed on the motor. OT-RK-390PH-5132/84.5.
If anyone is interested in it for 30 $ E-mail me and I'll send pics and anything else you want to know about it.. Thanks, My name is Todd t.shel@hotmail.com
Comment
-
Originally posted by Todd Shelton View PostHello, everyone. New to this site and I'm not sure if this is where i should post this, but who knows, I'll give it a try. I was given a Ferocious Frankie P-51 Mustang that has some damage. I don't know if it crashed or something else happened to it, because the tail section, with the flaps, is what' messed up. there is no battery or remote.. The only reason i kept it is because it just looks so Damn Cool. Anyway I'm not going to go buy a battery and a remote just to crash. If anyone is interested in it for parts. This is what's printed on the motor. OT-RK-390PH-5132/84.5.
If anyone is interested in it for 30 $ E-mail me and I'll send pics and anything else you want to know about it.. Thanks, My name is Todd t.shel@hotmail.com
Comment
-
Originally posted by Aros View PostI haven't tried on 3S but I would probably go with 60% power on 3S... Here's a link to the prop...I bought 3 and have only needed the 1 so far.
Unfortunatly, this prop cannot be sent to my country.
Closes I found is this
Is it the same thing?
Comment
-
Not sure if that's the same prop...I did have to do some basic modifications if I recall to the spinner...My YouTube RC videos:
https://www.youtube.com/@toddbreda
Comment
-
Originally posted by Irish_steve86 View PostHi guys I'm new to this. What's the best process for applying these transferes
If my explanation doesn't make sense, just google search waterslide decals and I'm sure a ton of directions will pop up. Best of luck too you!
Comment
Comment