Originally posted by Wobisch
View Post
Announcement
Collapse
No announcement yet.
3d Printed Part Sets - Freewing F-4D Phantom II
Collapse
X
-
Biggest progress I made using this ABS S filament combined with a Lokbuild adhesion plate and a cover for my ultimate 2+. I also switched from Cura to Simplify 3D Software. Since then I can do much better parts. I had to learn using less temperature (230°) instead of 250° I started with. Build plate is heated up to 90° instead of 100° to avoid "Elefant Foot".
Since then printed a lot of DirtyDee's Parts. I really appreciate his work for the community.
- Likes 2
Comment
-
Originally posted by Wobisch View PostHi this is a special ABS S filament which has less shrink rate.I solemnly swear to "over-celebrate" the smallest of victories.~Lucky B*st*rd~
You'll never be good at something unless you're willing to suck at it first.~Anonymous~
AMA#116446
Comment
-
Originally posted by Dirty Dee View PostNot to be duplicating efforts, but I made a 600 gallon centerline tank as well. Bartered with dlxpkg for a pair of wing bags for my A-10 in return for a printed centerline tank:)
Some design differences from apmech1's, like utilizing the stock FW hardware as well as I added the aft sway braces. Will upload to thingiverse after I finish printing them and make sure they are good.
Comment
-
Originally posted by Dirty Dee View Post
Scratchbuild. I posted plans on RCGroups under my blog. Im actually considering selling it to make room for my current A333 project.
- Likes 2
Comment
-
Originally posted by Derek.motionrc View PostJust finished my cockpit, the parts look really good and it was a fun project now to do the nozzles and the pilots are from Jet Hanger Hobbies.I solemnly swear to "over-celebrate" the smallest of victories.~Lucky B*st*rd~
You'll never be good at something unless you're willing to suck at it first.~Anonymous~
AMA#116446
- Likes 1
Comment
-
Originally posted by apmech1 View PostAny suggestions or requests for 3d parts for these airplanes?
If you could work on:
A TailHook for this that'd be WaaaaayCool !! Printed in (L)(R) Halves that would be bonded to a Center Structure for increased strength and Durability !! The Wire Capture Ends would need to be Removable as well due to their getting Ground Down on the asphalt upon landing. The pivot assembly and Attachment Forebody should have an internal framework of Plywood or Carbon Fiber with the 3DPSkins or Outer Shells attached to that !!
Operating Canopies// Frames and Pivot assemblies
Also a Standard ARM for my WildWeasel and some AGM-88s Please !!
3 Photos
- Likes 1
Comment
-
Originally posted by Bobaroo View Post
Hey,.. I have a few requests...
If you could work on:
A TailHook for this that'd be WaaaaayCool !! Printed in (L)(R) Halves that would be bonded to a Center Structure for increased strength and Durability !! The Wire Capture Ends would need to be Removable as well due to their getting Ground Down on the asphalt upon landing. The pivot assembly and Attachment Forebody should have an internal framework of Plywood or Carbon Fiber with the 3DPSkins or Outer Shells attached to that !!
Operating Canopies// Frames and Pivot assemblies
Also a Standard ARM for my WildWeasel and some AGM-88s Please !!
Comment
-
Originally posted by Derek.motionrc View PostJust finished my cockpit, the parts look really good and it was a fun project now to do the nozzles and the pilots are from Jet Hanger Hobbies.
Pilots looks very awesome! Did you use the 1/10 scale or 1/12 scale pilots?
regards
Dave
- Likes 1
Comment
Comment