Callie Graphics

Official FlightLine 1600mm P-51D Mustang Thread

Collapse
X
Collapse
First Prev Next Last
 
  • Time
  • Show
Clear All
new posts

  • davegee
    replied
    Well, today was drop tank and bomb drop demonstration day with the P-51. I printed four (4) 500 pound bombs, two with a removable bolt in the nose for better ballistic trajectory and two with a removable scale nose fuze that can easily be used as droppables when you remove and replace the nose fuzes with the bolt.

    I have two of the stock OEM 75 gal. foam drop tanks, today was their second drop test.

    Also, I printed two large scale 110 gallon drop tanks, designed by Danger Dan Gross and I printed them up and converted them to be able to be dropped from the wing pylons of the model

    First flight I dropped the OEM tanks, flawless, again. No issues with them in the least. Very impressive and well played by Flightline.

    Second flight I ran a few racetrack patterns to be sure the 500# bombs were secure, and then came in for a fairly low level bomb drop as it passed perpendicular to my position with the transmitter. Again, flawless, they departed the airplane cleanly together in tight formation, and hit the dirt after a graceful somewhat ballistic arc to the ground. The noses dug into the dirt a bit, no damage at all. Very happy about that.

    Last flight flew the large scale 110 gallon long range tanks. It was obvious that the plane struggled just a bit due to this extra weight and drag, mostly drag, but they seemed pretty solid. Once I flipped the switch to release them, nothing happened. I tried a few more times with the switch, and then decided to bring it in with the tanks attached for a normal landing. That did occur, but once the airplane touched down, both tanks dropped off and rolled to a stop. Just light cosmetic scratches, no real damage.

    So, two of the three tank drops worked perfectly, the third went ok, with the notable exception not releasing when commanded. However, I did it several times on the ground, and of course it worked perfectly each time! So, there are some minor adjustments to do before the next test flight with those on board. Overall, I was pretty pleased with how things went.

    I'll attach some pics of earlier today. Later this month I hope to get Dan at the camera and take some shots of the tank releases and post on HS.

    Cheers

    Davegee

    Click image for larger version  Name:	IMG_3874.jpg Views:	0 Size:	148.2 KB ID:	451832 Click image for larger version  Name:	IMG_3865.jpg Views:	0 Size:	210.8 KB ID:	451833 Click image for larger version  Name:	IMG_3867.jpg Views:	0 Size:	173.8 KB ID:	451834 Click image for larger version  Name:	IMG_3872.jpg Views:	0 Size:	184.2 KB ID:	451835 Click image for larger version  Name:	IMG_3870.jpg Views:	0 Size:	180.8 KB ID:	451836



    Leave a comment:


  • davegee
    replied
    Originally posted by f4u ausie
    Shop looks great Dave. Almost to good 4 a workshop
    Yeah, Almost!! But that awful carpet just HAD to go!! You should see the work bench in our garage. That might look more appropriate for what you were expecting!😁😁😁

    Actually, the people who we bought the house from almost 7 years ago, the wife made dog clothes in that room for little frilly dog pets. For us, owning bulldogs, that just wasn't going to fly. She had all these little sparkling sequins hidden in the carpet that we kept finding for years!


    Cheers

    Dave

    Leave a comment:


  • f4u ausie
    replied
    Shop looks great Dave. Almost to good 4 a workshop

    Leave a comment:


  • davegee
    replied
    Originally posted by jetfool
    Davegee,
    Nice bombs and that shop looks great. I need to clean mine, so many things I'll never use again.
    Our daughter and husband are driving to Oregon to visit some horse people and we hope they don't have trouble with the smoke and fires.
    Best Regards, Rex
    Thanks, Rex. I'll attach a pic I just took prior to a bomb drop test on the work table into soft pillows for the bombs. Worked perfectly, and I hope to do a flight test next week if the smoke clears out.

    It's hard parting with some things that you have had for a long time. Today we just let go of some snorkeling/diving gear that we used on vacations and on my expedition to Palau in 2014. We just weren't going to use this stuff anymore, and it's good to free up space. A little sad, but that is life moving on, I guess.

    Hopefully your daughter and her husband won't have problems with the smoke in Oregon where they are going. For us, the worst is that horrible human-set fire that destroyed almost 1,000 homes and structures in Spokane, WA. But it all moves east and if you are in the downwind path, you get it. We have a beautiful mountain just north of us a few miles called Heart Mountain, about 8,500' tall, MSL. Looking out my window right now, you'd not even be able to convince anyone such a natural mountain that tall even existed, for the smoke!

    Cheers

    Dave

    Click image for larger version  Name:	IMG_3860.jpg Views:	0 Size:	126.3 KB ID:	451732

    Leave a comment:


  • jetfool
    replied
    Davegee,
    Nice bombs and that shop looks great. I need to clean mine, so many things I'll never use again.
    Our daughter and husband are driving to Oregon to visit some horse people and we hope they don't have trouble with the smoke and fires.
    Best Regards, Rex

    Leave a comment:


  • davegee
    replied
    This last week I've had workers in our house to redo my workshop. Instead of the old carpet that seems to "swallow" anything I drop on it like screws and such, this is a wood plank floor (probably faux wood). It looks so much better and brightens things up a ton! Plus, it was time to do a thorough cleaning and assessment of things I really need, versus things I don't use, won't use, and are better off in the trash. A lot more organized now and I hope to keep it that way.

    On the FL P-51D front, I am working on finishing up my droppable 500# bombs that I printed up from Cults. I will be putting a replaceable bolt in the nose for weight to make it drop realistically, hopefully. I have done that with smaller printed bombs that I drop out of my FL B-25 and they work great.

    Assuming dense smoke from forest fires further west from us like Spokane start to shift or die down, I'll try drop testing these bombs next week. I do have an identical set for static display I printed that have all the scale details on them, like nose and tail fuzes. I have already done a drop test from the airplane on my bench, and they should work just fine, I think. But that smoke is bad news. Besides eyes burning and coughing, I had a bit of a scare flying my F9F Cougar turning a long final approach the other day. The grey color of the plane just made it disappear in the smoky skies! I just kept looking for it, not changing the position of the sticks on my transmitter, and then, Out it Popped! I don't want to tempt fate twice on that score!

    Here's a couple pics from this morning making bombs and my new shop look.

    Click image for larger version  Name:	IMG_3856.jpg Views:	0 Size:	75.7 KB ID:	451726 Click image for larger version  Name:	IMG_3857.jpg Views:	0 Size:	98.9 KB ID:	451727

    Leave a comment:


  • davegee
    replied
    Glad you’re Back!!!

    davegee

    Leave a comment:


  • Grossman56
    replied
    Holy cr@p!! I finally got back on !!!
    It's like withdrawals when you can only look in but not participate!!
    Now I'm afraid to log out!

    Grossman56
    (Dangerous Dan)

    Leave a comment:


  • davegee
    replied
    I got two flights on my HHH P-51D Flightline Mustang this morning, and got to test dropping the OEM 75 gal. drop tanks. I was ready to do more tests if anything went wrong, but the first test was perfect. The two tanks landed only about 8 feet from each other after being dropped from an altitude of 80 feet or so. No damage at all to the foam tanks afterwards.

    Also flew my Cougar, and a great flight on it, too.

    Next week, I hope to do a drop test of my scale 500# bombs from the same pylons used today. We’ll see how that goes. After that, once I get the shackles I ordered from MRC yesterday, I’ll drop the larger tanks currently in development.

    davegee

    ​ image widget

    Leave a comment:


  • davegee
    replied
    Originally posted by jetfool
    Davegee,
    Fantastic work! Qudo's to you and Dan on designing extra scale acc. for this plane. Have you seen on the other forum where a guy has installed an operable inner cooler/exhaust door underneath the fuselage. Kinda neat
    Best Regards, Rex.
    Thanks, Rex. Weather permitting, I'll be flying HHH tomorrow morning at my local field and test out dropping the 75 gal. fuel tanks to see how that goes. I have already flown them "captive," lightly glued onto the foam pylons to test if they had any bad effects on flying the airplane. Absolutely no problem with them attached, so it will be neat to see how they depart the airplane. These Flightline pylons have two spring-loaded plungers that put some pressure on the drop tanks or bombs, so that when they are released, they are pushed away from the airplane with gusto. Not sure if that is all that necessary or not, based on all the drop tank tests I have done with other aircraft, but it isn't a bad idea, I guess. Maybe the designers saw something in testing that they wanted to be sure the drop tanks would quickly get out of the way when released, lest they hit the airplane, or something.

    Yes, I have had P-51s before that had that feature with the aft cooling flap on the underneath of the fuse. That could certainly be done on this airplane, although if I add something down the raod, I might buy that detailed cockpit kit to dress up the airplane interior.

    I'm very happy with this P-51 overall, and think it will be one of their better sellers among warbird enthusiasts.

    Cheers

    Davegee

    Leave a comment:


  • jetfool
    replied
    Davegee,
    Fantastic work! Qudo's to you and Dan on designing extra scale acc. for this plane. Have you seen on the other forum where a guy has installed an operable inner cooler/exhaust door underneath the fuselage. Kinda neat
    Best Regards, Rex.

    Leave a comment:


  • davegee
    replied
    Hi All: Well, it only took 45 days to receive my P-51D drop tank mounts, but I'm glad they are finally here. I think the hang up wasn't with the supplier, RC Castle in Hong Kong, but rather I think it got delayed getting through US Customs in LAX. Once it finally cleared there, USPS got it to me in just a few days. I have ordered a second pair of these mounts as a backup, but for now, whenever they come someday is fine.

    So, Flightline designed this airplane to be able to drop OEM 75 gallon foam fuel tanks on the wings with these mounts. As I reported before, I think the shape and size of these scale drop tanks is quite good, and I commend the designers at Flightline for their work. I am hoping later this week, possibly even tomorrow, I'll test out dropping the OEM tanks to see how they do.

    But, I didn't want to stop there. I bought an STL through CULTS and scaled up 500# bombs to 1/7 scale to also drop using the same mounts. That is still a work in progress, but I'll post a couple pics today. They do indeed work to drop during very preliminary tests this morning.

    Also, Danger Dan and I are working on a larger scale drop tank, but there is still some more design and building work to do before we unveil that one. We hope to test all three of these various droppables later this month. Hopefully we can get some inflight photos of these departing the airplane. It's sorta fun thinking outside the box to get these things accomplished. It's all fun!

    Cheers

    Davegee

    Click image for larger version  Name:	IMG_3851.jpg Views:	0 Size:	75.3 KB ID:	451650 Click image for larger version  Name:	IMG_3852.jpg Views:	0 Size:	42.7 KB ID:	451651

    Leave a comment:


  • Aros
    replied
    Wow, late to the party but that 3D printed cockpit sure looks sweet. I wish it would come that way out of the box. I would gladly pay the extra cost if FW shipped them that way.

    Leave a comment:


  • Elbee
    replied
    Hugh Wiedman

    Saw your vid on ewe-toob and it's excellent.

    Love the sight and the sounds.

    Really great modification, Hugh.

    Logical to the exteme and performs as it probably should have from the OEM.

    Well done, Sir.

    Best, Steve

    Leave a comment:


  • Hugh Wiedman
    replied
    Finally got a video of the motor upgrade to the FMS 1700mmP-51. I know this thread is about the FL 1600mm, one coming here soon :hugging:, but no thread for the 1700mm, so just getting in the way as usual. No idea how fast it is, only that it has loads of power and easily climbs and cruises at 50% throttle. The Mr. RC Sound card works OK, but obviously can't match a MOKI!:triumph: Landing was a bit crappy, but came in a bit hot :fire: since I was used to the old motor having to land around 42% throttle. With this motor, 25% is more than enough to get a smooth 2 point landing.

    Leave a comment:


  • Evan D
    replied
    Click image for larger version

Name:	IMG_8764.png
Views:	254
Size:	213.5 KB
ID:	451590 Manual states to do a throttle to down elevator mix for this exact reason.

    Leave a comment:


  • nuts-n-volts
    replied
    I just create a throttle to elevator mix. About 5% on the -51, if I remember. You want the mix to start at about 30% throttle and reach the 5% down elevator when the throttle maxes. I'll have to go down to the Tx to see exactly what I'm using for this Mustang. ...But, it's late and I just had a pretty busy day. I do this for any plane that does not have a correct thrust angle and can't be easily corrected because of a big spinner. Jets can use this trick too.

    Leave a comment:


  • GliderGuy
    replied
    Originally posted by f4u ausie
    Hi guys hope you are all well!!! My flying buddy has now got this plane looks great. He is finding once trimmed or a better explanation may be. It changes trim.. if U set elevator at full throttle at half it dives. So U then retrim it. At full it then rises at full. Any one else have that apparent trouble. Is that called zoom climb??? The f4 does that but very minor only at full speed Chris wolf had a mix in his red phantom
    Trim settings are only valid at a given CG, speed, and throttle setting. Change any of these, and you must retrim. In full scale aircraft, the pilot gives the trim wheel a work-out. No one setting fits all conditions all of the time.

    That being said, usually you can find a trim setting that works “most of the time”. Why? Because the designer sets the wing, vertical stab, horizontal stab, prop angle to counter speed and throttle setting changes. Some planes are better than others.

    -GG

    Leave a comment:


  • Elbee
    commented on 's reply
    I get it. My first scale model was a Coverite Gee Bee Model D kit. Symmetrical airfoil and the horizontal stabilizer was parallel (same incidence) as the wing. I was told by one of the R/C pattern aircraft guys that was the issue with trim changes at different throttle settings. I have yet to have that explained to my satisfaction, hence my comments. Could be motor thrust angles, too, for argument's sake. Would be interesting to take a model where the trim settings stay fairly constant and measure the incidences and thrust angles to compate against your buddy's Mustang. Could be something, could be nothing.

  • f4u ausie
    replied
    Steve unfortunately I don't no the answer. Twice. Daaaaa. Me. But it is this new p51

    Leave a comment:

Working...