It from guidance and, being prepared to know the difference. No such thing as Luck! When you enjoy when people smile, it should ring a smile back. Friendships are so important in life. (134) E-Flite Carbon Z Prometheus Taking It To The Limit! Fun Flight And Review by Merry Boozer RC - YouTube something to share with you.
-
-
Does anybody make parts to make the canopy open on the A-10?? Thank you. JohnComment
-
See post below...scroll up to 9910 and read down to 9918 for more info and possible contacts who might help.
#9918
Mar 30, 2020, 06:07 AMComment
-
Does anyone know where to find an stl for modified exhaust nozzle to correct thrust line? Originally I had seen a post about them but the links to thingiverse returned 404 so I have searched and searched but no luck yet. Thanks!!Comment
-
CS, were the A-10a nozzles you are looking for on Thingiverse, designed by Dirty Dee?
If so, DD has smartly moved all his designs to the Cults3D website.
Check there anyway, his nozzle design is top-notch.
Best, LB"I am having an extraordinary ordinary life."~Lucky B*st*rd~
"Find satisfaction in the process rather than an outcome."~Anonymous~
AMA#116446Comment
-
Thanks!! I will check it out.Comment
-
-
"I am having an extraordinary ordinary life."~Lucky B*st*rd~
"Find satisfaction in the process rather than an outcome."~Anonymous~
AMA#116446Comment
-
Went to print them and my x axis motor crapped out. Ah well. Next weekend!!!
Comment
-
Got the printer running again. Side note, stepper motor Anti-corrosion coating had began to come off stator and was causing excessive dragging this the motor issue, ultrasonic cleaner for a couple minutes and clean up with a plastic bristle brush runs like a champ again.
Got the nozzles printed. But how to remove the stock nozzles without tearing up foam? Any pointers? They seem to be glued in? I can’t see any glue but they are firmly in place. Get rough with it? Or is there a secret to taking them out?
thanks!!Comment
-
"I am having an extraordinary ordinary life."~Lucky B*st*rd~
"Find satisfaction in the process rather than an outcome."~Anonymous~
AMA#116446Comment
-
LB, thank you sir. I went ahead after reading your post and just worked around the edge with x-acto and then worked the nozzle around some. It did come loose with a little paint :-) but as you say nothing shows with the new nozzle in place. Thanks so much!
Comment
-
Morning all
I'm looking in to getting the Freezing A10 and apologies if this gets asked a lot.
Is there a list/record of all the mods so I could make an ultimate A10, add ons, mods, improvements and tweaks. Does anyone sell mods ready to install as I don't have a 3D printer and work away on ship a lot so things already painted would be ideal.
This is the package I'm looking at, any recommendations for the electronics such as Gyros, and such that would dramatically help out with balanced flight and keeping her steady for take off and landing?Attached FilesComment
-
-
Well everyone has his own list but i fly of grass and very bumpy runway with a real gear bender/braking reputation.
nose gear mod: railer link and 3d printed brace (must i.m.o)
Main gear mod: 3d printed brace.
i have the as3x /safe reciever but i only use it when landing, in flight only AS3X.
I use the landing flaps with up elevator mix since this i never made a bad landing again. this model is well known of bumpy landing when you dont land it the right way causing it to bump the nose gear badly.
Im a big gyro fan because it helps out with smoother flights.
I think the 80mm is fast and strong enough. I fly with 5600 80c packshot and get 7min with storage volt left in the packs. But im thinking about going to 5000mah.Comment
-
I currently have the V1 A10 and fly with my CG at 95mm. I have printed the new thrust nozzles but would like to know if I should now move my CG forward? Thanks for any help.
CFComment
Comment