Alternative motor windings and drive schemes

[Clugh]

Hi,
You have to be a member and signed in to see the photos from here on out.

I'll leave data when its complete with a new winding.

But check out the 3DP semi magnetic slot wedges I made for a higher efficiency Scorpion HK5020

Thanks
Hubert

[Clugh]

Muncie.is right around the corner....

[Clugh]

And why are you not testing "syncloss" now for Audisosmith? I bet you dont even have a AC amp clamp or DC wattmeter on the bench. feeding the inverter. You have a scope dont you? Why haven't you captured the BEMF waveforms the comparative motors make using the scope in FFT mode and calculated the Thd using a prime mover to drive the motors as generators ?

The Comtrol YY motor works perfect as a prime mover the new motor is the perfect brake

Drive three halogen candles with the motor terminals and the load is on when all three open end are shorted to one another. You can do that with 3 transistors and vary the load with duty cycle at the on gates. You can even use another inverter connected to the braking motor in active freewheel on the battery end you can drive a dc load, recharge a battery, or strap some type of braking resistor across it. Heater elements will work.

What data and capture equipment do you have Dr Okon besides unilog.?

Where is the control Y or YY motor at the same or similar Kv and its constants Dr Okon? You forget scientific method when you test things?

[Clugh]

#2 was a 12 turn YY wound with 1.25mm. So only 1 turn more than the hybrid and it had larger wire. Do you see what the idle current Kv and operational temperature rise from ambient was Dr Okon.

P700 YY
12 turns parallel wye in 1.25mm
Copper cross section 14mm^2
Kv 527
Io 2.7 amps @ 20 volts
ΔTemp @ 5min from ambient = +5 °C

P700 Hybrid
11 turns (4T)Y + (6T)Δ in 1.20 mm
Copper cross section 12.4mm^2
Kv 410
Io 1.51 amps @ 23 volts
ΔTemp @ 5min from ambient = +3°C

Only you cant see the writing on the wall. and yours never agrees with academics and is always a secret. BTW you notice Docta at WOT, which is six step for yge's, the larger wire dual layer YY with more fill ran hottest of all the motors on the YGE at 8khz pwm and zero degrees timing???? In a dual layer It will have the most sinus like waveform away from BLDC drive mode of the inverter so torque ripple is maximum with it at full throttle with the YGE.

No one even records idle current amperage to the 3rd decimal. Tell another story or show them the incorrect routing and motor constants that came with it. You never showed the backside termination of your hybrid wound motor for the forums.



TTYL
Hubert

[Clugh]

The Hybrid P700 does a lower Kv with 4 less turns than a YY and it ran cooler despite less fill. and at a significantly lower idle current. Less turns in this case made it much lighter than all the other motors in the Cambridge test but with 4 less turns you can run alot larger wire with it. Larger wire with less turns drops the DCR. The mis already wound with a larger wire than the YY 1.15mm to 1.20mm

The YY's idle current is 2.1 amps at 18.9 volts the hybrid is 1.51 amps at 23.49 volts After 5 min The YY who's idle would be even larger at the same voltage ran at 33 degrees Celsius the hybrid 24 degrees Celsius

[Clugh]

Yeah that's wtf I thought! You still HAVE NOT left a single unit of data. o youre still a full joke to US but figure you better wind ya HK and test it before I leave them the real data. And what measuring equipment you use when you are not testing the right way nor are your reporting the idle currents. You still think your friends in Germany and American are stupid huh? Funny how my post drummed the bs back up again. Silly man hiding his comparative constants on a motor he says he has no use for but he is testing it again and still asking for data. You're so damn bright and weird you cant realize nobody in the world has any data to offer a clown but the English speaking Anglophiles. ..There's a million ways to test its effectiveness that doesn't require a 10,000 Yokogawa PA WHICH the IEEE top test equipment HAS ALREADY SHOWN THE IMPROVEMENTS BTW ! Despite that its very easy test.for a hobbyist it s obvious to everyone but a moron that loss translate theat. If the pm and bell have reduce loss even close to the projected numbers common sense would tell you you can look at the bell temps oif a motoro in operation and you can always turn a freaking prop and look at consumption. You know all that so please continue with the Minstrel show. You rather me expose you step for step. Ok cool go ahead with that. Let US and them understand .You're interested in anyone's data on a motor winding your application has no use for? We're glad you finished your unreported data yet still have interest. You really think the hobbyist are stupid....and cant see the dents in your reptilian armor No one In the world has any data on the external rotor hybrids but POCBOY....That's why you are here in class. Remember? Dr Okon You haven't posted a single thing of any scientific comparative relevance YET! I also see you aint ask ya buddy in Bayern or explain why it wouldn't be suitable for a hobby speed plane LOL!. See how you skew fact and I expose it easily? That always happen with fact versus fiction. Do you expect different results if you keep lying? It is mania, the sudden shift in opinion and emotions, u 2 go through daily. Its like menopause.

"If someone tests this as well and comes to different results, I would be a bit interested."
"As written:
if someone should find out otherwise, I would be interested."
~Dr Ralph Okon~

"The no-load currents show differences max. in the (unreliable) 3rd decimal place."

And I know that's a lie there's no way the idle current is the same... what would you need any more comparative data if the phase resistance was the same with no change in idle current between the two machine that run at the same Kv The hybrid is a slower machine for sure therefore it can also hold larger wire becuase it uses less turns. Thats clear in the P700 data from the "Anglophile" in Cambridge UK!

This is why real engineers leave data and not social media mania. Its even more simple why he wont leave any constants because that would mean someone could check his falsified recollection of data.

Where are the recorded comparative motor constants on these 10 and 14 pole motors you supposedly and fairly tested with the control wye wound machine dude? Comparing a 10 pole motor and a 14 pole motor on the hybrid winding isnt a comparative test . The effect will be exactly the same on both engines.

Where is the control wye wound motor and its constants Dr Okon??????? or you trying to confuse the forum again by comparing things not in question like two different pole rotors on the same wind .


Hubert

[Clugh]

Ralph Okon!

I bet you wont ask or tell Christian Lucas directly in that German thread exactly why a hybrid wind work for your application and any other e traction application in hobby or recreational that use a 12 slot 10 pole machine.. And he wont ask or tell you a good reason either!

Or you both could come out the closet and answer me here directly since you are both here. You know you both are posting a bunch of nonsense over there in Germany!

You laid up together now AFAIC which is incredibly funny but you see the data here on the subject matter....you two got some???



Danke,
Hubert

[Clugh]

A serial wound 5 turn wye + 9 turn delta hybrid on the Pyro p650 is going to bring a Kv of approximately 536.@ 1o degrees timing on the castle Hydra Ice HV 200 v2 there would be numerous ways to route it and still end up with the equivalent circuit just like the conventional windings. You can also wind hybrids with only 6 wires and no solder points if you know how.. but a proper silver solder join creates a cooling sink right at the connection nodes of the delta and wye machine.



perfect attendance....

You know you need a weekly regimen of medication too because you could just talk to me and make these ridiculous proclamations you are in Germany right here direct Ralph... You plum crazy just like Luke cap.


Tell me is this deep GER-mania u2 suffer from?

[Clugh]

KONTRONICS PYRO P700
4 turn wye + 7 turn delta Hybrid

Have a close look at number 3

Americans motor heads can determine from the Kv and no-load currents and turns counts compared to the conventional windings if there is an improvement in efficiency. Its enough here to make that obvious determination if the Dr and his friend in Bayern know anything about electric motors and physics which they do, so they are a sad couple when they play laurel and hardy and concurrently falsify information about electric motors on the GSM.

They both are already aware of this data.

This crazy alter ego powercroco doesn't need any data from his German forum colleagues to compare when he knows full well they do not have any

This was the first attempt by a hobbyist, so the doctor has to work on his skills, because as you can see, it fit, the engine was running and the data came along..

What's the doctor's problem, guys?

Pure nonsense!....

Wenn er die Kabel nicht richtig verlegen kann, ist das sein Problem, nicht Ihres!!! Der Grund, warum er diesen dummen Thread überhaupt gestartet hat, ist, dass er seinen eigenen Thread wegen der Schuld des Witzbolds nicht wieder eröffnen kann.



He tells you his application has no use for it which is VERY false but still what about all your own individual applications readers.... Do not listen to it. It's nonsense!

TTYL
Hubert

[Clugh]

Das Komische, Dr. Okon, ist, dass ich auf Ihrem Bild sehen kann, dass Sie den Hybrid mit einfacher Stern-Dreieck-Schaltung gewickelt haben. Es handelt sich nicht um eine Parallelschaltung wie bei mir, daher sind Ihre Kabel lang, genau wie bei einem Motor mit einfacher Stern- oder Dreieckschaltung. Die Verwicklungen durch Ihre Verlegung sind Ihr eigenes Problem. Schlagen Sie es nicht als Problem für andere vor, denn die gleiche Version wurde mit dicken Drähten auf einem 700er in Cambridge, Großbritannien, gewickelt.

[Clugh]

So don't be too confident about his thumbs up in agreement to your statement about the hybrid.. He only put that thumb up ya booty because he is still here and tries to remotely to annoy me.

He knows the winding works and works very well ,so please be careful with the company you keep Dr Okon....

You see he said no one on the forum knows anything about electric motors especially the crocoman, so I wrapped it all up for you in a 4 post package so the.modus operandi in Bayern is understood by all the thumbs

He can offer you a thumb to tickle your fancy but not any empirical data on the star - delta hybrid winding on 12 slot 10 and 14 pole external rotor BLDC machines like you inquire about.



Take care....
Hubert

[Clugh]

[Clugh]

[Clugh]

[Clugh]

Hi Dr Okon.

[Clugh]

[Clugh]

You can certainly find high voltage electrolytic caps that can deliver that type of instantaneous amperage but you still have to find the high voltage source to charge them.

BUT have you ever seen or heard the arch flash at just a 480 V 600 ampere fuse tripped from a dead short?. You can mess this one up not knowing what you are doing if you want to.



You gone have one time to "f" it up an you will not have to worry about it ever again cap because you are done if you get hit !!!

Ya exit is gone be like my boy in Bayern without the chute !!!





But seriously if you find some transformers that can push it you can build something. if you take the right precaution you can do it safely. I've seen lower voltage magnet zappers systems around 600 volts with 600 volt caps so you might get away using transformers out of a commercial microwave oven to charge them.

[Clugh]

A deeper idea of what is involved with post assembly magnetization if you want to magnetize the non polarized segments. So you have unpolarized pm material that you can easily glue into place then magnetize them after the rotor is assembled.. Note the voltages and amperages involved in a two shot method out of their magnetizer. The last time I've seen that much juice is servicing huge industrial spot welders at Daimler that welded the Body ribbing on the school busses. The huge cables to the spot welders were water cooled.. This huge thing probably is water or oil cooled in the caps and high voltage transformers.

This is truly how you pull motor magnet segmentation off if you do not buy pre segmented pm
Post-Assembly Magnetization of Rare-Earth Fractional-Slot Surface Permanent-Magnet Machines Using a Two-Shot Method

• M. Hsieh, Yao-Min Lien, David G. Dorrell
• Published in IEEE transactions on industry… 3 October 2011
• Engineering, Physics

[Clugh]

How do you on the GSM talk about motor improvement with purely a winding then suggest any of these other methods anyway? They are not windings and have nothing to do with winding. This is rotor and pm manufacture. A pressed pre fabricated litz coils is also not hand wound.

you want motor improvement with purely a wind but dont want to change what you currently wind.

Make that make sense...

Show me some data and they will acknowledge you again.




The P650 5Y + 9D parallel hybrid in 22awg
Kv 1072
Rm 28.3 milliohms
Io .7 amps @ 16.5 volts

Till then you are welcomed to look here and figure each other out because we plan to keep doing what we do here in the American winding program.

Bi Bi...
Hubert

[Clugh]