Alternative motor windings and drive schemes

[Clugh]

Brenner made it into the prelims but ended up around 46 place from what it looks like. There were some really good pilots there according to the report. I'm always still in development and as you can see there is room for improvement ALWAYS.... Andrew reported an empirical gain of 10 % of efficiency with the machine in his 25P flight program. According to him that gives him extra maneuvers. Its a very technical and complicated flying.

In 3d Andrew flies' ego drift if I'm not mistaken. He inquired but I haven't wrapped one yet. I'll do it for him soon enough.

[Clugh]

1. Andrew Jesky - USA
2. Lassi Nurilla - Finland
3. Tetsuo Onda - Japan

Team
1. USA
2. JAPAN
3. AUSTRIA

"Andrew put up an absolute barn burner flight precise, concise, and geometrically accurate. No snaps or lines missed, he seems to slow his pace just a little or moved out a little making some subtle adjustments lowering his box top but it was like a Machine I’ve never seen a better flight from Andrew"
~Andreas H~

Andrew runs a VLV with this Clugh 8+8 yy in 17 AWG. Who cares if Dr Okon tried to hate on US!!!!

What do the motor Fuhrers have to say now????

Like I told ya'll boys.......I WILL NEVER KISS THEIR RINGS!

I plan to stay "psychopathic", "dimwitted", and "American" till I die.

Danke,
Hubert

[Clugh]

In front of the second unknown (flight #9) in places 1 to 3 are:

Andrew Jesky - 1968.75
Tetsuo Onda - 1963.89
Nurila Lassi - 1953.77

Where are you at Dr Okon? AJ is at the top!

See the "Americans"

Hubert

[Clugh]

On the other hand currently every German speed prop is OFF the open market. Think its a coincidence??? That's all you have left so I know you'll NEVA send me a prop for any head to head comparisons. You all talk buddy.. Somehow I dont think restricting them to your buddies only now will work with me..... I'm more capable than you'll ever know.

An American will have to build his own now. So we will..... . Did I tell you the tungsten disulfide spray is also an incredible release agent???

Back to enjoying the boats.... I've let u2 and your remote nonsense take me away from that.

TTYL
Hubert

[Clugh]

You wont even post how much your version weighs....And I actually pay attention to the worthy post there.

[Clugh]

You can send your highest pitched croco blades in Germany here for 12000 rpm and I'll turn them direct drive and geared. What do you want to do but remain silent and learn here?



Danke
Hubert

[Clugh]

Do you really want some of this "American Supermotor" Dr Okon? Because you can get it as soon as you produce some data!
Neumotors is already in another Class!!!

I also own the cuts with full rights to build and develop the estranged and jaded Christian's 24 slot super engine and the 125mm cut he brags about all the time. Fully permissioned by him.....Did he tell you that?

So you know what to do....right?


Hubert

[Clugh]

Do you wanna play with my 24 slot AMERICAN super engines? How? you cannot master the 12 slot yet.

Id be happy any day youd like to compare but first youll need data!!!

[Clugh]

Slick-33 weist den niedrigsten Reibungskoeffizienten auf, den wir je erreicht haben – lediglich 0,0467 % CoF gemäß ASTM D2266-Standard.

Stellen Sie sicher, dass Sie und der Motorenchef in Bayern überhaupt wissen, wie hoch der Reibungskoeffizient des Schmiermittels in Ihren NMBs ist oder was auch immer für ein Unsinn er verwendet, Dr. ... Sie beide haben keinen Schimmer, was wir hier verwenden, es sei denn, ich sage es Ihnen! Oder sogar, was Ihre eigenen Lager verwenden ...

Kopieren Sie es!

Es ist einfach, HYPE!!! zu tippen.

Danke
"Der dümmliche Amerikaner" mit der höheren Effizienz

And you are still here in the "psychopaths" class err day.....

[Clugh]

Hallo Dr. Okon, ich sehe, wie Sie auf der Suche nach mehr im Forum herumstöbern. Wir haben die Hybriddaten, die Sie angeblich haben, noch nicht gesehen. Dasselbe Geschwätz in die Threads anderer Personen einzubetten, funktioniert nicht. Ich kann sie alle lesen. Ich bin auf dem Laufenden.

Wo ist der Datenzuhälter?


Hubert

[Clugh]

The Russian Cyclon .40 is 3.2 kw at 31,000 rpm it weighs 310 grams. A Dubb Jett 40 is 340 grams. The p600 depending on the wind will be between 315 and 340 grams all day and the lil bomb can peak around 5kW at 30,000 so that is what the little power turd can do... Its extremely potent and scary on the 7X10 direct drive even at 8 s lipo. .I'm not running THAT in my kitchen. I tapped the throttle on the Futaba 10PX a few times and said oh hell no..... Its also quite loud.

I cant find the .40 pylon prop i just purchased to test. I have so much junk around here I lose things right in my face....When I find it and finish setting up a power supply that is not my drag cells i will run it on the various scrap iron around here.

36 true EV cells. They have plenty of capacity and I wont have to worry about solder tabs etc. These are real cells! for the reactionary torque cradle that's only limited by the motors own RPM which will be optically tach' ed.

[Clugh]

The little 600 is right on pace with the best pylon engines. If you think about it its a little stronger. The last Metketmeijer Brothers .40 benched @ 2.5Kw at 30,000 rpm.

[Clugh]

If I build a dedicated engine for the purpose the bearings would be turbine grade ceramics so about 300 dollars for a pair. They will never be replaced! and can run well over 100,000 rpm with load rating about 3 or 4 times a hobby grade radial bearing.

An NMB is not an electric motor quality bearing. That's fact. Its a general purpose bearing that works good enough for the average hobbyist. People looking for custom wound engines with 5 to 10 thousand dollar planes are not the average hobbyist though.
That would be a goal.

We have a different design philosophy. You want to perform yearly maintenance which you will so severely underpowered but if its possible Id like to not ever see engine I built again! To me that's a worthy goal One may never achieve but that's certainly what a customer would prefer. Endless running.

But im not greedy like some people....

I also wonder if legendary nitromethane engine builders like Henry Nelson or Dubb Jett said. "oh well that's good enough"

[Clugh]

Now Im off to wind 2 more 650 growlers for 2 more TDR's to control the helifreaks.. See the horrible "smearing the American does"???? Your friend in Bayern was also wrong about the ceramic bearings he has no clue about the special lubricant we use unless I told ya, which is the slickest in the world.

You all are so high end with the pure insulator UHU endfest and 5 dolla NBM's. How could we ever compete...?

You should ask Lucas what the coefficient of friction is on the grease his steel bearings use or that packed in a NMB or maybe even your 7455 bearings from CHINA! Louis asked you about.

They are surely trash....if its not Swiss German or Japanese made I don't want it in my motor PERIOD! You can install and run the garbage into the ground. I'm absolutely elated about that....


Layta Gator
Hubert

[Clugh]

Were still using Boron nitride here in America

[Clugh]

Dr. Okon, ich erkenne auch die Heuchelei darin, dass Sie diesem neuen Wickler, der seinen Stator ziemlich gut gewickelt hat, sagen, Sie trauen der Wicklung nicht, weil sie sich lösen kann, obwohl Sie derzeit nichts an Ihren Motoren verwenden, trotz all dem Gerede über Aluminiumoxid. Als der Wickler Sie fragte, womit er seine Drähte befestigen soll, ignorierten Sie ihn, um sich nicht ins Fettnäpfchen zu treten.

HK4225 Croco Winding | Page 3 | RC-Network.de!


What a hypocrisy! His winding is as safe as yours which also uses nothing to secure your wires.

[Clugh]

Hi m reading more speed BTW

"The new Typhoon Ultra max was ready in time for the GSC. Thanks to Marcus for laminating.
Let's see how it goes at the weekend.
Drive Scorpion HK5050 (Powercroco) with 16S SLS Speed cells and YGE ESC prototype."

~Thomas Moldtmann~

The response

"The load should weigh about 6kg, so it needs at least 25kW, good luck!
Where is the CSD reported?"

~Audio smith~

And he's right since scorpion only reports 11kw for a 5040 so it will be grossly underpowered if it need 25 kW!!! its at least 10 short. no one will average 600 kmh with it because no one ever has....

[Clugh]

Hallo, ich sehe, du bist noch da. Was hast du vor? Deine Freunde warten sicher auf eine würdige Erwiderung ...

[Clugh]

Ohmical Dr? Ohms law is just one law in electronics. There are many others laws and theorems concerning various circuits in electronics.

Try Faraday's



Get some sleep buddy....

[Clugh]

Itz funny . The 4225 was 1 milli the align was 5 milli but the ETA was 3% points higher with 5 times your resistance. and a much better Io