Alternative motor windings and drive schemes

[Clugh]

Andrew Jesky's 650 gained 10 percent empirically . Who did I copy because Bert never wound for Andrews VLV contra drive...

So you see Ralph has not a clue what he is talking about and is simply jealous.

[Clugh]

I dont know why you would mention anyone machines when running at 69% and burning up everyday. . A motor from Steve Nue never sees such low performance levels. U truly only need concern yourself with you own below average efficiency. despite all the pretty copper.

Why call out the high end if Thomas sinks you by 10 points with a Joker 50 dollar motor.? U need to discuss your efficiency with his empirical charts you say you trust.

His efficiency calculation shows the motor as a real soldering iron

why doesn't Ralph Okon. The leader. have his own empirical charts?

[Clugh]

Fri, Jul 26, 2024 at 1:17 AM

"Hi Hugh,


The sheet metal cut in the Lehner external rotor motors has more iron in the stator tooth. For more torque you need more iron, you know that.

Your tuned engines are great, no question about it. If torque density is also important, sheet metal cuts with less iron have a problem: saturation occurs and the controllers lose commutation. The Lehner do not lose the commutation, even during hard accelerations in the vehicle when really high currents flow. The Heinis didn't put as much strain on the Lehner engine as necessary to show what it was all about. They're cowards. They didn't load up to the synclos. They would also have had to use a different number of turns on the Lehner that delivers the same speed under load, but they didn't. And so far no one has used a magnet system that increases magnetic flux. Flukleitkeil and Halbach magnet systems are necessary for highest performance. I also sent you the article by Dr. Andreas Grundel sent, who shows the current internal rotor with flux compression magnet system and flux barriers in the stator. I'll get the Hybried ceramic steel ball bearings and then build a Lehner 4125 with such systems with a CFRP bell, which will be lighter like the Scorpion etc. engines.


Best regards

Christian"
See your own words? Anakin? You know for yourself the weight is the problem. But you dont report you want to be light LIKE A SCORPION to German social media so I did it for you.

So they see all your bs. The fallacy wont work around here. I never listened to this email because my applicable load point for the motor is 158 amperes. No one claimed anything else. The stock 700 mx does it easily.

It this what he says was remotely locked in as the only way it doesn't explain his 2260 or 3040 he suggest. They have no teeth. he just needs to worry about himself and his own motor problems.

I have not said a single thing about losing sync with my castle. Thats them talking with the trash inverters they run. and have no idea what goes on in the American kitchen without indication from me.

I literally have folders of similar contradiction like Lehner wouldnt let you do 14 poles. remember that email buddy? And all you friends there can read how you feel about them too..

Everyone is stupid but you but you still hang out with all the "slow" people. Why?

[Clugh]

Lies you dont know Jim Allen and you introduced yourself to me. I did not know you fool. So u can stop lying..... he never cared a flip about you.. He literally asked me where I get you from LOL!

We knew enough about Europe to save you aryan ass from Stalin. My uncle served in Germany so again you dont know a damn thing about what Americans know you cant even speak English and its a very easy language to learn.

Man so may people feeling would be hurt if I posted what JA though about forums and certain members. YOU THINK YOU KNOW THAT BLACK MAN trust me you didnt. He actually made me promise to take suckers like you out. And so here we are....

We had plenty of discussion about your superiority complex which he questioned it validity coz you have no degree like us.
Would you like to see that email?

You know you dont know him because you cant ever spell his name correctly . Go sit your old lying ass down somewhere.please

Boy you funny and making a fool of yourself telling more lies

It is really sad this level of mental pathology.

U are sick man really!!!

If you knew me youd have my phone number a REAL address u have neither but I have yours i dont know why your on the forum the only thing u do there is hold up JAGS boat which they almost sued you for

They dont like you either and say you are a real nuisance at the row pool in munich . U tried to get them to produce their SAW boats for the masses and they laughed in you face and basically told you get lost.

I have the emails from Gunner you have zero to do with the boat. Ive fact checked every lie youve ever told me by contacting the people direct.

You a liar Christian almost all the time for forum attention.

This is why i do things like contact merian at YGE and will be contacting kontronics today, Im tired of you lying to hobbyist than know no better.

Sure everyone is fooled. No one knows your reading here. Ive been Ralph teacher 100 time out your mouth but you dont read here...



I gotta go I don't have any more time for forum fraud. You wont get anything accomplished in RC. You haven't in 20 years and can barely walk and look like you weigh about 20 pounds wet.. I feel sorry for you.. You really think the hobbyist are slow and know no better. Ive never seen lying like this in 53 years on my Mama..

Its pitiful u really need help

Later
Hubert

[Clugh]

Edit if you dont have a running Halbach with data or a 20 pole just be quiet no one cares about the mystery machines or is going to get excited over your 93% thick tooth motor. If that isn't apparent yet keep plugging away...

Albert is not thinking about your 41 he likes his 4030 and 4020 xnova

and it is the 24 slot 8 pole I suggested that you and Ralph said doesnt work as well as a 12N20 P but he is flying and you are typing its 50 grams lighter the winding factor is 1 an she can sink 6.4 kw ETA 93.2%


They spec better because they are lighter and lose nothing to your 41 in power or efficiency just like said.

Ralph hurry! you go run tell him since he doesn't read here..


bye bye

[Clugh]

Boho1
Member
Last Activity: Today, 11:41 AM
Joined: Sep 13, 2023
Location:

hey puddin'

Please observe the XNOVA 4030 motor specs better than both your motors and it gets higher pilot reviews as well. U see Albert Fruth flies it...

Its psychopathic

.

[Clugh]

Another Easy drama free choice that the Pilots actually like and performs great. The black and gold can stay in Dresden.
Listening to dude talk about what Americans know is funny. He visited FLA and had to email me and get clarification just to understand the speed limit here.


His intellectual superiority to us dumb Americans is really something to behold even with such simple things as mph to kph. Most dash clusters in America have both indicated .
But "we're dumb"

[Clugh]

On 4-14-2025 @ 22:57 hundred hours Christian Lucas wrote:

" From the scraps of my helicopter an air coil outrunner with Halbach array for Sollarflug was created, which a friend of mine made, no I didn't send it to the stupid American, he wouldn't have made anything out of it."

[Clugh]

.



I'm trying to tell y'all boys It isn't me. This man has a real problem with truth bay bay.

Ill talk to you later.. I really do not have any more time for this nonsense. Just believe what you would like but I'm not a brand seller in your technical section and that's the end of the story. I just wind motors. I cant keep this up lie for lie. I could. I have folders on the man, but I think you have more than enough evidence he just talks out the side of his neck because he is salted.

He's definitely not posting anything truthful. I hate to bust ya bubbles but I think you know todays date.

These 2 are cuu cuu. and believe their own lies I guess.... You see I have his helicopter lamination right here.....

keep listening to him crocoworld.....



TTYL
Hubert

[Clugh]

Read the words and youll understand how a Salamander slides.and why it camps here.

"In contrast to you, he - no matter how crazy he wants - has wound at least a few motors himself in recent years.
And in addition to these thiird - hand winding copies smeared on the outside with thermal conductive mumpe, I even tried something new with his Y-D my self."

~Powercroco 4-14-2025~

I've already won AGAIN because he is winding it in the dark away from the forum view. PowerCroco doesn't want you to know he copies my ideas like his open air wye bundles. He stole that from me.. You read his own words about team xerox yesterday.. told you Dr Gerlings wind didn't work so what is he trying the hybrid wind for guys?

Be upset that these 2 vendors have stood in the technical pages on every forum across America and lied directly to you face on everything from A to Z

You should be upset. Because they hold the growth of the artform of winding motors back tremendously they also skew your understanding by doing that. They promote thir brands not the science of it and that's why I do not care for Ralph and have no interest in associating with Lucas. They have lied way to much to you all and I don't think its fair.

They wont even let an American speak on their ****ty little forum.

Lucas shows photos 20 plus year old an if you look at the 41 LMT other than an open slot none of it is incorporated. It does not have these flat coils or flux focus arrangement he keeps showing you. Again what he did with a large engine does not translate down to a 5050.

Before id even listen to him id have to see something run. he literally hasn't moved a model under power in 20 years. Thate the truth . Please don't be led on by a sofa bandit in Bayern that is not at all active in RC. All this same crap he's showing today ive been looking at the last 12 years.

Not a things comes of it. you can use.

[Clugh]

3M Thermally Conductive Epoxy Adhesive TC-2810 Cream is a two component, boron nitride filled adhesive that offers low outgassing, good thermal conductivity, and low chloride ion content. 50 mL Duo-Pak Cartridge.

This smearing is 10 times more thermally conductive that the bs you do powercroco...

Croco "smearing" traps the heat in and helps to facilitate his burned up coils. He uses construction epoxy that softens at 100C See powercroco's potting work?

[Clugh]

When i used thinned high temp epoxy im still 10 times cleaner.
These coils are potted! In crystal clear HTE its stable to 200C
That other nonsense is his German croco work you can compare it to.. I would not buy it!

[Clugh]

Potted in the 3M TC2810 U go back and look at his UHU trash and he wants to talk about I'm smearing.

CHILD PLEASE YOU ARE A COPY CAT WIND TRASH AND YOURE ALSO SLOPPY!!!

This American has plenty for the hand crafted German trash coming out of Dresden.

[Clugh]

POWERCROCO German hand crafting doesn't use anything now to secure your coils so your wires can shake till you short and burn up like the rest of his DNF projects.



To me the difference between he and I are quite clear as the photos indicate. Besides he's still telling you it doesn't work but he cant match my numbers the way he does it.

TTYL
Hubert

[Clugh]

Good Morning!!!! Look at your potting work Powercroco. You critical of others?

[Clugh]

And about boats. Lucas You talk about scorpion like trash out on the open German forums but In America on our forum you post this:

Thats problematic if YOU are an Honest person. See you can't have it both ways. Like you will tell me Ralph is racist to stir a pot just because Im black yet you sent Ralph laminations and are in photos smiling with him. Thats association is it not????? And true manipulation to try to get me to side with you over Ralph. You are mad because I see through all that and i understand YOU aint have a single problem with Ralph what ever he is till now. YOU first tried to get me to let Ralph wind a motor for me and I told YOU absolutely not I can do my own work! This is the truth.

But think about how clueless you are in your own falsehoods if you say Ralph is this and that why would YOU recommend him to me when we first met.

You see you crazy and I cannot believe anything YOU say! Whatever Ralph is is his business I care less, so Its you that's this German that rides American stereotypes for all their worth trying to be manipulative using the most underhanded topic YOU could throw my way and it failed. The forum is about motors not Ralph's epithet and lack of morality. I am above it and apparently you're in with it. sheet sender , so look at yourself.



fast forward forums

Do you see what engines has mounted on the old prather lap cat II? Thats actually relevant to the bad things he says about scorpion. Its nice to grandstand with scorpions in still photo but the hull is also at least 30 years old. Never once has it run or turned at speed with this apparatus !!!! and you wont see that now either.

[Clugh]

Enjoy your spring lucass..... ill be looking forward to seeing YOUR boats run this year.

YT
Hubert

[Clugh]

..
The COTS 600Kv 4035 24N8P max eta is 94.53% the winding factor is 1. It weighs 506 grams

[Clugh]

[Clugh]

Where is the 12 slot 20 pole Christian? Albert Flies this 24 slot 8 pole Kw of 1 boo boo. that's 3 slots per pole. The 12N20P is .6 slots per pole. A 12 slot 4 pole is 3 slots per pole the exact equivalent to a castle in runner. A reference machine. For quiet and clean performance. .